Part Details

  • Bearing Type: Tapered Roller Bearing
  • Quantity: 4 Piece Set
  • Kit Includes:
    (2) Front Outer Tie Rods
    (2) Front Hub Assemblies

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 4 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side) 
  • Direct replacement
  • Built to strict quality control standards

What are Tapered Bearings and Why Use Them?

Tapered bearings are better than roller ball bearings at handling forces exerted on the bearing during cornering (known as axial load) in trucks and large cars. 

Roller ball bearings have spherical ball bearings between two straight rings (called races). Tapered bearings use tapered rollers shaped like flat-topped cones and two races angled from the outside to the inside of the bearing. The greater the angle, the more axial load the bearing can handle.

Your model came from the factory with tapered bearings. This type of bearing handles cornering forces better for trucks and large cars. Roller ball bearings work well for smaller cars, but replacing a tapered bearing with a roller ball bearing will result in increased wear and faster failure.

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (0:41)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:13)
    • Turn the wheel by hand
    • Remove the 21mm nut from the outer tie rod
    • Thread the 21mm nut on a couple of turns
    • Hold the tie rod with an adjustable wrench
    • Loosen the tie rod adjusting nut with an adjustable wrench
    • Strike the steering knuckle with a hammer
    • Twist the 21mm nut off the tie rod
    • Measure the distance from the tie rod boot to the outer tie rod stud
    • Note that measurement
    • Twist off the outer tie rod.
  3. step : Installing the Tie Rod (2:11)
    • Twist on the outer tie rod
    • Measure the distance from the tie rod boot to the outer tie rod stud
    • This should be the same as the distance noted in Step 2
    • Move the adjusting nut as necessary
    • Push the tie rod into the wheel knuckle
    • Fasten the 21mm nut onto the tie rod
    • Tighten the 21mm nut to 111 foot-pounds of torque
    • Tighten the adjusting nut
    • Twist the grease fitting into the tie rod
    • Tighten the grease fitting with a 7mm socket and ratchet
    • Add grease to the grease fitting with a grease gun
  4. step : Reattaching the Wheel (3:34)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Measuring Tape
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 21mm Socket
  • 7mm Socket
  • 10mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 21mm wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
great experience
fast quick service, great price for great parts. Everything fit as expected. No problems and very helpful videos to help you install parts.
September 18, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2004-2007Infiniti QX56 Infiniti QX56 4 Piece Set Steering & Suspension Kit
2005-2007Nissan Armada Nissan Armada 4 Piece Set Steering & Suspension Kit
2004Nissan Pathfinder Armada Nissan Pathfinder Armada 4 Piece Set Steering & Suspension Kit
2004-2007Nissan Titan Nissan Titan 4 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog ES800031
  • Moog ES800032
  • Hollander 538-59042, 538-59070
  • OE # 402027S100
  • OE # 402027S000
  • OE # 485207S025
  • OE # 486407S025
Part #: 1ASFK03225


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(04:25 min)