Specifications:

  • Brand new Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Pull off the hub cap
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Control Arm (3:49)
    • Straighten out the ball joint cotter pin, using a pair of needle noise pliers
    • If the cotter pin is stuck, cut the head with wire cutters
    • Then tap the stuck cotter pin out with a hammer and punch
    • Apply penetrating oil to the cotter pin if necessary
    • Pull the cotter pin out with needle nose pliers
    • Loosen the 19mm ball joint nut
    • Loosen the ball joint from the wheel spindle with a pickle fork and hammer
    • Remove the 19mm nut
    • Remove the two 17mm nuts connecting the ball joint to the control arm
    • Remove the 17mm bolt connecting the ball joint to the control arm
    • Separate the ball joint from the control arm with a pry bar
  3. step : Installing the Ball Joint (9:12)
    • Thread the grease fitting onto the new ball joint by hand
    • Tighten the grease fitting with a 10mm wrench
    • Put the ball joint into the wheel spindle
    • Thread the 19mm castle nut onto the ball joint stud
    • Lower the control arm with a pry bar
    • Put the ball joint bracket studs into the control arm
    • Fasten the 17mm nuts onto the ball joint bracket
    • Insert the 17mm bolt into the ball joint bracket
    • Tighten the two 17mm nuts to 94 foot-pounds of torque
    • Tighten the 17mm bots to 94 foot-pounds
    • Tighetn the 19mm nut onto the ball joint stud
    • Make sure the castle nut lines up with the cotter pin hole
    • Insert the cotter pin sideways, with the longer leg facing in toward the center of the vehicle
    • Bend one of the cotter pin legs around the nut with pliers
  4. step : Reattaching the Wheel (11:53)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 17mm Socket

  • Specialty Tools

  • Pickle Fork

  • Wrenches - Metric

  • 17mm Wrench
  • 19mm Wrench
  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Will this kit fit a 1999 Toyota Camry LE V6?
Mario L on Feb 20, 2016
BEST ANSWER: Yes, according to the information you supplied, the part you’re looking at will be correct for your vehicle. If you have any other questions or would like to place an order with one of our customer service representatives, please feel free to give us a call.

Vehicle Fit

  • 1997-2000 Lexus ES300 10 Piece Set Steering & Suspension Kit
  • 2001 Lexus ES300 10 Piece Set Steering & Suspension Kit (Built Before 7/01 Production Date)
  • 1997-2003 Toyota Avalon 10 Piece Set Steering & Suspension Kit
  • 1997-2000 Toyota Camry 10 Piece Set Steering & Suspension Kit
  • 2001 Toyota Camry 10 Piece Set Steering & Suspension Kit L4 2.2L (Built Before 7/01 Production Date)
  • 2001 Toyota Camry 10 Piece Set Steering & Suspension Kit V6 3.0L
  • 1999-2002 Toyota Solara 10 Piece Set Steering & Suspension Kit
  • 2003 Toyota Solara 10 Piece Set Steering & Suspension Kit (Built Before 6/03 Production Date)

This part replaces:

  • OE # 4333039435
  • OE # 4504629255
  • OE # 48830-06020
  • OE # 4881006030, 4881033010
  • OE # 4882006030
  • OE # 4550339135, 4550329355
  • Moog K9499
  • Moog K90313
  • Moog K90311
  • Moog K90312
  • Moog EV301
  • Moog ES3306
Part #: 1ASFK02543


How-to Video:

(14:09 min)