Part Details

  • Quantity: 12 Piece Set
  • Kit Includes:
    (2) Front Upper Control Arms with Ball Joints
    (2) Front Outer Tie Rods
    (2) Front Lower Control Arms with Ball Joints
    (2) Front Sway Bar Links
    (2) Front Inner Tie Rods
    (2) Front Lower Adjustable Ball Joints

Specifications:

  • Brand New Control Arm, Tie Rod & Sway Link Kit
  • Comes as a 12pc Kit
    • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

 

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

An adjustable ball joint will look slightly different than a standard, non-adjustable version.  The stud will be offset once installed and can be rotated in order to allow a greater range of vehicle suspension alignment.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (0:56)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Control Arm (1:23)
    • Remove the 18mm bolt and washers from the control arm with an 18mm socket and breaker bar and 21mm wrench
    • Loosen the 22mm nut on the bottom of the ball joint with a socket and breaker bar
    • When the nut is flush with the end of the bolt, hit the nut with a hammer
    • Remove the nut with a 6mm Allen key
    • Pull the ball joint up and out
    • Pry the control arm out of the subframe with a pry bar
  3. step : Installing the Control Arm (4:55)
    • Insert the lower control arm into place
    • Insert the 18mm bolt and washers into the control arm but do not tighten all the way
    • Insert the ball joint into the knuckle
    • Push down on the ball joint and tighten the nut, and use an Allen key if necessary
    • Tighten the 21mm ball joint nut to 50 foot-pounds and add 90 degrees
    • Use a jack to push up on the lower control arm to put the weight of the vehicle on the suspension OR
    • Complete step 4 before continuing
    • Torque the 18mm bolt to 130 foot-pounds
    • Remove the jack
  4. step : Reattaching the Wheel (8:24)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    Allen Wrenches

  • 6mm Allen Wrench

  • General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Safety Glasses
  • Gloves

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Wrenches - Metric

  • 21mm wrench
  • 22mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Who makes these parts?
E J on Aug 21, 2018
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. If you have any further questions, please don't hesitate to ask.

Vehicle Fit

Year Make Model Description
2005-2010Chrysler 300 Chrysler 300 Rear Wheel Drive 12 Piece Set Steering & Suspension Kit
2008-2010Dodge Challenger Dodge Challenger 12 Piece Set Steering & Suspension Kit
2006-2010Dodge Charger Dodge Charger Rear Wheel Drive 12 Piece Set Steering & Suspension Kit
2005-2008Dodge Magnum Dodge Magnum Rear Wheel Drive 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Dorman 521-121
  • Dorman 521-122
  • Hollander 512-01474L
  • Hollander 512-01473R
  • Moog K620258
  • Moog K620257
  • Moog K620177
  • Moog K620178
  • Moog K80823
  • Moog K80822
  • Moog ES3571
  • Moog EV80702
  • Moog K7469
  • Reference Number MS25120
  • Reference Number MS25121
  • Dorman 521-007
  • Dorman 521-008
  • Hollander 511-01108L
  • Hollander 511-01107R
  • OE # 4872717
  • OE # 4895482AB
  • OE # 52106710AC
  • OE # 4895483AB
  • OE # 4872716
  • OE # 4895483
  • OE # 52013468AC
  • OE # 4782740AB
  • OE # 4782741AB
  • OE # 4895482
  • OE # 5180606AA 5180606AB 4782612AC
  • OE # 4782665AB
  • OE # 5180606AA 5180607AB 4782613AC
  • OE # 68028831AB
  • OE # 4782666AB
Part #: 1ASFK02313


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(08:50 min)