Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   8 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Outer Tie Rods
      (2) Front Upper Ball Joints
      (2) Front Strut & Spring Assemblies

These replacement suspension parts are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • FRONT Suspension Kit includes:
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)*
    • (2) - FRONT LOWER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT UPPER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Strut & Spring Assemblies -  LH (Driver Side) & RH (Passenger Side)
  • Parts are new, not remanufactured or refurbished
  • Direct replacements
  • Built to strict quality control standards

*NOTE: For 2002 Models, there were two different tie rod options available: 1st design (14mm thread) & 2nd design (16mm thread). This tie rod is correct for models with the 2nd design tie rods.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (0:46)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Ball Joint (1:11)
    • Separate the axle from its housing with a pry bar and a hammer
    • Unclip the brake line from its clips
    • Remove the ball joint retaining ring with a hammer and punch
    • Remove two 10mm bolts from the steering knuckle bracket
    • Apply penetrating oil to the control arm nut and bolt
    • Remove the 15mm nut and bolt from the control arm
    • Strike the control arm with a hammer to loosen it
    • Pull the steering knuckle forward
    • Support the wheel knuckle with wire ties
    • Cut off the ball joint boot with a razor
    • Fit a ball joint press to the ball joint
    • Tighten the press to press out the ball joint
    • Remove the ball joint press
    • Tap out the ball joint with a hammer
  3. step : Installing the New Ball Joint (4:22)
    • Push the new ball joint into place
    • Fit the ball joint press onto the ball joint
    • Tighten the ball joint press to press in the ball joint
    • Tap the ball joint in with a hammer
    • Tap the snap ring into place with a hammer and punch
    • If you are replacing the snap ring, put the new ring on with snap ring pliers
    • Push the steering knuckle into place
    • Push the control arm onto the ball joint
    • Tap the control arm onto the ball joint with a hammer
    • Start the 15mm nut and bolt into the control arm
    • Remove the wire ties from the steering knuckle
    • Push the axle into its housing
    • Tighten the 15mm nut to 50 foot-pounds of torque
    • Fasten the grease fitting onto the ball joint with a 10mm wrench
    • Add grease to the ball joint with a grease gun
    • Insert the two 10mm bolts into the steering knuckle bracket
    • Clip the brake line into place
  4. step : Reattaching the Wheel (7:00)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer
  • Razor Blade / Gasket Scraper

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bearing Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket
  • 10mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Grease Gun

  • Wrenches - Metric

  • 15mm Wrench
  • 10mm Wrench

4.50/ 5.0
6 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
5
0
0
1
0
Free shipping
The parts Good quality and easy to install. 1A videos are really helpful. Im definitely going to use 1A again
July 24, 2017
best prices
fast delivered i would recomended 1aauto nice customer services thanks i save money for others thinks
August 1, 2017
Great price and Quality Parts.
Beats the price of the competition by half. Wont buy parts anywhere else.
August 7, 2017
Great product,timely delivery,great prices, over all wonderful buying experience
March 22, 2018
Great service everytime
Orders always received within 3 business days and great prices for good quality parts. Very pleased everytime over the past few years.
May 30, 2018
Indirect patt
I ordered a front end suspension kit for my car and after I got the car to the shop only to discover they sent me an incorrect mail joint for my car. I had to go to the local shop and purchase one since I had already scheduled time with the shop and mechanic. Very disappointing!
August 11, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2007Buick Rainier Buick Rainier 8 Piece Set Steering & Suspension Kit
2002Chevy Trailblazer Chevy Trailblazer 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2009Chevy Trailblazer Chevy Trailblazer 8 Piece Set Steering & Suspension Kit
2003-2005Chevy Trailblazer EXT Chevy Trailblazer EXT 8 Piece Set Steering & Suspension Kit
2002GMC Envoy GMC Envoy 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2009GMC Envoy GMC Envoy 8 Piece Set Steering & Suspension Kit
2003-2006GMC Envoy XL GMC Envoy XL 8 Piece Set Steering & Suspension Kit
2003-2008Isuzu Ascender Isuzu Ascender 8 Piece Set Steering & Suspension Kit
2002Oldsmobile Bravada Olds Bravada 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2004Oldsmobile Bravada Olds Bravada 8 Piece Set Steering & Suspension Kit
2005-2007Saab 9-7X Saab 9-7X 8 Piece Set Steering & Suspension Kit
Part #: 1ASFK02066


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(07:51 min)