Replaces

Steering & Suspension Kit - 1ASFK01858

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   14 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Tie Rod Adjusting Sleeves
      (1) Pitman Arm
      (2) Front Outer Tie Rods
      (2) Front Sway Bar Links
      (2) Front Upper Ball Joints
      (1) Idler Arm
      (2) Front Inner Tie Rods

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 14 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct fit replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Remove the wheel (1:00)
    • Loosen the lug nuts.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Remove the front shield (1:15)
    • Use a 15 mm socket and ratchet.
    • Remove the four bolts.
  3. step : Remove the Idler Arm (1:25)
    • Remove the 24 mm bolt securing the idler arm to the steering linkage
    • Use a joint fork and a hammer to separate the joint.
    • Remove the three other bolts securing the idler arm.
    • Use a Tie Rod Puller to pull apart the idler arm and the idler shaft.
  4. step : Install the new idler arm (4:34)
    • Assemble your new idler arm to your idler shaft, threading on the bushing and nut.
    • Bolt in the idler arm assembly into place, tightening up the three nuts.
    • Bolt in the end of the idler arm assembly to the steering gear.
    • Torque the nuts and bolts to 80 ft lbs.
    • Install the cotter pin.
    • Use a grease gun and fill the grease fitting.
  5. step : Reassembly (7:25)
    • Replace the shield with the four 15mm bolts.
    • Clip the air bag harness back in.
    • Put the wheel back on and lower the car
    • Using a star pattern torque the lug nuts to 120-140 ft lbs

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 22mm Socket
  • 24mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Fork
  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench

4.64/ 5.0
11 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
8
2
1
0
0
Prefect fit
Fixed my steering issues. Now my tahoe drives straight!
January 25, 2017
Even being of smaller diameter than the factory HD components they seam to work well and are of excellent quality. Shipping was fast!
July 31, 2017
Very good package/kit. Thank you would purchase again
August 15, 2017
Suspension kit
Parts are nicely machined and fit with out any problems.
February 23, 2018
Amazing deal!
Got it early than expected. Also the cheapest around. Couldn’t be happier
April 12, 2018
Parts
The package came when expected, everything was there.We are very happy!!
April 17, 2018
14 pc steering and suspension kit
Great deal. Decent parts at a very good price. If I had purchased these parts individually at my local parts store it would have cost over 4 times as much. The install went well and now it is time for a wheel alignment. Thanks guys!
May 1, 2018
I would totally recommend for anybody who likes to working in their own cars That you wont be disappointed On the parts and of the customer service they are the Best 1A auto.com
October 1, 2018
Everything I needed
Purchased this for my 95 Tahoe worked great and good price fast delivery
October 10, 2018
Suspension Kit
The Chevy kit I purchased was full of quality parts, however the lower ball joints were the wrong set for my vehicle.
November 24, 2018
Fast and spot on
Everything went well parts came fast great service
December 7, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Are all of these part greaseable on this kit part #1asfk01858?
Jacob S December 6, 2015
Yes, there are tapped holes and zerks on every movable joint. I had to buy a right-angle nozzle for my grease gun to reach the Pitman zerk as it sits directly beneath the stabilizer bar. Be sure to install the lower ball joints with the zerks facing the rear at an angle so you can grease them once installed.
Brian L December 6, 2015
Yes Jacob all these parts are greaseable let me suggest u get a good ball joint press and start your lower ballpoints as straight as possible and keep it straight by moving press from each side of lower arm take your time and good luck you can do it.
Anthony G December 6, 2015
All parts are greasable and come with fittings but you might want a couple of 90 degree fittings because the pitman and idler arm are hard to get to once they are installed. Just a heads up I had to order new upper control arms because the upper ball joints and arm had been replaced with a riveted unit that could not be separated.
Tyler T December 6, 2015
Yup good buy! And yes all grease able
Alexander S December 7, 2015
Yes, and come with new zerk fittings. Would not recommend for heavy off road use or as an HD replacement.
A C July 31, 2017
WILL THIS WORK WITH A 4 IN LIFT?
Sandy S February 19, 2016
Everything but the pitman arm will work. You probably have a drop pitman arm with the lift kit so it is a special item that will need to be purchased seperatelt
Cecil W February 19, 2016
Yup it will I have a 7.5 lift.
Alexander S February 20, 2016
No it will not
Michael C February 21, 2016
Though we have posted other comments for your question here, please note that this is NOT correct for anything over 2.5-3 inches of lift.Steering geometry will be harshly be effected. Sway bar end links will not position the sway bar in its effective range either. This is not recommended. Because the parts fit does not mean they will "work".
Brian F February 22, 2016
What brand is this?
Shayne H January 5, 2017
I dont know remember what brand it was, but it is working fine. Most of these parts are made over seas and are supposed to be oem specifications. Hope this helps.
Thomas B January 5, 2017
We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. If you have any further questions, please dont hesitate to ask.
Tim K January 5, 2017
What exactly comes with this kit? The photos seem kind of generic and I can’t find a parts list in the description
Jacob R October 14, 2017
This kit comes just as pictured, and are all for the front end. Here is a list for you: Idler arm Pitman Arm Lower ball joints Upper ball joints Outer tie rods Inner tie rods Sway bar links Tie rod adjusting sleeves
Tim K October 16, 2017
How do I know if my pickup has stamped steel lower control arms?
M O October 24, 2017
You may physically confirm this by looking at the control arms, or you may contact a local dealership with your VIN to confirm this information.
Alex P October 24, 2017
Our VIN decoder is not detailed enough to provide this information.
Alex P October 24, 2017
Which is the inner tie rod and which is the outter 402-17A01 402-07B03?
Marl C March 27, 2018
Im not too sure on part numbers, but you can look them up separately on 1aauto website search.
Christopher A March 28, 2018
If you have received these items and are looking to identify them you can look up the 1A part numbers on our website. Thank you!
Adam G March 28, 2018
Year Make Model Description
1995-1999Chevy K1500 Truck Chevy K1500 Truck 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
1995-2000Chevy K2500 Truck Chevy K2500 Truck 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms 6 Lug Wheels
1995-1999Chevy Suburban K1500 Chevy Suburban K1500 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
1995-1999Chevy Tahoe Chevy Tahoe 4 Wheel Drive 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2000Chevy Tahoe Chevy Tahoe 4 Wheel Drive V8 5.7L 14 Piece Set Steering & Suspension Kit Stamped Steel Lower Control Arms
1995-1999GMC K1500 Truck GMC K1500 Truck 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
1995-2000GMC K2500 Truck GMC K2500 Truck 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms 6 Lug Wheels
1995-1999GMC Suburban K1500 GMC Suburban K1500 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
1995-1999GMC Yukon GMC Yukon 4 Wheel Drive 14 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2000GMC Yukon GMC Yukon 4 Wheel Drive V8 5.7L 14 Piece Set Steering & Suspension Kit Stamped Steel Lower Control Arms
Part #: 1ASFK01858


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(08:13 min)