Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as an 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
do all parts have greaseable fittings?
glenn g on Jun 2, 2016
BEST ANSWER: no. pregreased and sealed

Vehicle Fit

  • 1998-2001 Ford Explorer without Sport Package 8 Piece Set Steering & Suspension Kit for Models with One Piece Design Control Arm
  • 1998-2011 Ford Ranger 2 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1998-2011 Ford Ranger 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
  • 2001-2009 Mazda B2300 Truck 2 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1999-2001 Mazda B2500 Truck 2 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1998-2007 Mazda B3000 Truck 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
  • 1998-2007 Mazda B3000 Truck 2 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1998-2009 Mazda B4000 Truck 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
  • 1998-2009 Mazda B4000 Truck 2 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1998-2001 Mercury Mountaineer 8 Piece Set Steering & Suspension Kit for Models with One Piece Design Control Arm

This part replaces:

  • Hollander 511-01056BR
  • Hollander 511-01057AL
  • OE # 1F703224X
  • OE # 3L5Z3083AA
  • OE # 5L5Z3A130AA
  • OE # F57Z3280AA
  • OE # F57Z3280HB
  • OE # F87Z3A130BA
  • OE # ZZP03224X
  • Dorman 520-221
  • Dorman 520-222
  • Moog K8695T
  • Moog K8694T
  • Moog EV317
  • Moog ES3461
  • Moog K8694T, K80771
  • Moog K8708T
  • Moog K80068
Part #: 1ASFK01097

How-to Video:

(13:53 min)