1ASFK00730-Steering & Suspension Kit 6 Piece Set

Replaces

Steering & Suspension Kit 6 Piece Set TRQ PSA58693

1ASFK00730

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Upper Ball Joints
  • Quantity: 6 Piece Set

This part replaces:

  • Moog K6663
  • Moog K6664
  • Moog ES3675
  • Moog ES3676
  • OE # 8191336700
  • OE # 19133670
  • OE # 22157319
  • OE # 26100287
  • OE # 26100286
  • OE # 22157320
FREE SAME DAY SHIPPING
Save 26%
List: $93.95 Save: $24.00
Part 1ASFK00730
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: PSA58693
Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Part Details

  • Quantity:   6 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Outer Tie Rods
      (2) Front Upper Ball Joints

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (0:46)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Ball Joint (1:11)
    • Separate the axle from its housing with a pry bar and a hammer
    • Unclip the brake line from its clips
    • Remove the ball joint retaining ring with a hammer and punch
    • Remove two 10mm bolts from the steering knuckle bracket
    • Apply penetrating oil to the control arm nut and bolt
    • Remove the 15mm nut and bolt from the control arm
    • Strike the control arm with a hammer to loosen it
    • Pull the steering knuckle forward
    • Support the wheel knuckle with wire ties
    • Cut off the ball joint boot with a razor
    • Fit a ball joint press to the ball joint
    • Tighten the press to press out the ball joint
    • Remove the ball joint press
    • Tap out the ball joint with a hammer
  3. step : Installing the New Ball Joint (4:22)
    • Push the new ball joint into place
    • Fit the ball joint press onto the ball joint
    • Tighten the ball joint press to press in the ball joint
    • Tap the ball joint in with a hammer
    • Tap the snap ring into place with a hammer and punch
    • If you are replacing the snap ring, put the new ring on with snap ring pliers
    • Push the steering knuckle into place
    • Push the control arm onto the ball joint
    • Tap the control arm onto the ball joint with a hammer
    • Start the 15mm nut and bolt into the control arm
    • Remove the wire ties from the steering knuckle
    • Push the axle into its housing
    • Tighten the 15mm nut to 50 foot-pounds of torque
    • Fasten the grease fitting onto the ball joint with a 10mm wrench
    • Add grease to the ball joint with a grease gun
    • Insert the two 10mm bolts into the steering knuckle bracket
    • Clip the brake line into place
  4. step : Reattaching the Wheel (7:00)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer
  • Razor Blade / Gasket Scraper

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bearing Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket
  • 10mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Grease Gun

  • Wrenches - Metric

  • 15mm Wrench
  • 10mm Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
2004-2007Buick Rainier Buick Rainier Steering & Suspension Kit 6 Piece Set
2002Chevrolet Trailblazer Chevrolet Trailblazer with 16mm Thread Outer Tie Rod Steering & Suspension Kit 6 Piece Set
2003-2009Chevrolet Trailblazer Chevrolet Trailblazer Steering & Suspension Kit 6 Piece Set
2003-2006Chevrolet Trailblazer EXT Chevrolet Trailblazer EXT Steering & Suspension Kit 6 Piece Set
2002GMC Envoy GMC Envoy with 16mm Thread Outer Tie Rod Steering & Suspension Kit 6 Piece Set
2003-2009GMC Envoy GMC Envoy Steering & Suspension Kit 6 Piece Set
2003-2006GMC Envoy XL GMC Envoy XL Steering & Suspension Kit 6 Piece Set
2003-2008Isuzu Ascender Isuzu Ascender Steering & Suspension Kit 6 Piece Set
2002Oldsmobile Bravada Olds Bravada with 16mm Thread Outer Tie Rod Steering & Suspension Kit 6 Piece Set
2003-2004Oldsmobile Bravada Olds Bravada Steering & Suspension Kit 6 Piece Set
2005-2009Saab 9-7X Saab 9-7X Steering & Suspension Kit 6 Piece Set

Part Interchange

Brand Label Part Number
DIY Solutions SUS00148
DIY Solutions SUS00185
General Motors 22157320
General Motors 22157319
General Motors 26100286
General Motors 19133670
General Motors 26100287
MOOG K6664
MOOG ES3675
MOOG K6663
MOOG ES3676
MOOG Chassis Products ES3675
MOOG Chassis Products ES3676
MOOG Chassis Products K6663
MOOG Chassis Products K6664

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: PSA58693
Product Reviews
3.50/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
1
1
0
0
Pleased
I was well pleased with my recent purchases The parts are of good quality and the price is great Im left comfortable with knowing that 1a provided me with long lasting durable parts
July 19, 2017
Ball joint
Overall good products, used several of them in the past work no issues. Except this time one of my new lower ball joints came with a slit in the rubber boot. Will have to get a new one to finish the job.
December 10, 2017
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Steering & Suspension Kit 6 Piece Set TRQ PSA58693-1ASFK00730 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.