Replaces
Part Details
Why Buy Monroe OESpectrum Shock and Struts?
Monroe OESpectrum Shock Absorbers and Struts are designed to be direct replacements while improving handling. Some of their benefits include:
Item Condition:
New
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the rear shocks on this 2003 GMC Envoy. It's the same procedure for all these SUVs: Envoy, trail blazer, Ascender, Ranier,. We show you the right side; the left side's the exact same procedure. Always replace your shocks in pairs, and you'll need new rear shocks from 1AAuto.com, 18mm socket and ratchet with an extension, and it helps to have a deep socket, an 18mm wrench. You can do this without even jacking up your vehicle, but for the video, to make it easier, we do put it up on a lift and use a jack.
Your rear shock is held in with an 18mm bolt up here and an 18mm bolt down here. Using an 18mm socket and ratchet, and 18mm wrench, just loosen up this lower bolt and hit it out as far as you can with the wrench. We'll fast forward as he loosens up the top bolt. You don't have to entirely remove them until you've loosened both of them. That makes it a little bit easier. If you are using jack and hack stands, have the jack stands supporting the frame of the vehicle, and then put some upward pressure on the rear axle with your jack to take some of the load off of the shock. I'm just watching the top of the shock to see it compress some. Now with the bolts loosened, you can pull the lower bolt out and then pull the top bolt out. You see that? Then it pulls free.
Up top, is the old shock. Below it, is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same. Feed your new shock up into place and replace that top bolt to hold it in place. Now, you'll need to line up the lower hole and this I only have to push up a little bit. If you have your vehicle on the ground you'll have to push it up more, push the shock up and then put the bolt through. We'll fast forward as Mike tightens those both up. Right now you're just tightening them preliminarily, although you can, if you're working without a jack and jack stands, and the vehicle's on the ground, you can tighten them up. What we do is we start up the vehicle just to give the air suspension a chance to inflate and make sure the vehicle's at its correct ride height. Then once we know it's at the correct ride height tighten up the bolts for the shocks.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Okay, friends, one of the first things we need to do is safely raise and support the vehicle, so your wheel's off the ground. Once you've done that, we're gonna come right here to your center cover. Use a nice little pry bar, and go ahead and pop this off. Now that we've done that, we're gonna remove all 6 of our 19-millimeter lug nuts and take the wheel off.
Now that we have the wheel off of here, we have a nice clear view of the rear shock. We're gonna start by removing this 18-millimeter bolt right here, and then we'll just start it back in just a few threads. Okay, so that's pretty good right there. It's pretty much ready to come out. At this point, let's make our way down to the bottom.
So for the next step, if you're working on a lift and you're jacking it up by the frame of the vehicle, what you're also gonna need to do is go ahead and put something underneath the differential so you can bring this up a little bit to take the pressure off the shock bolts. Now I'm gonna use my 18-millimeter wrench to hold this side of the bolt, and I'll remove this 18-millimeter nut. There it is, friends.
Okay, friends, it's time to install our new shock. One of the first things you need to do when it comes time to installing your shock is to make sure you charge it up. Let's get right down on the ground. Okay, we have our shock on the ground here, facing straight up and down. I've got it securely between my feet so it can't slide out on me. I'm gonna carefully press this down until it bottoms out, and then I'll let it completely rise up. After it's done that, I'll repeat the process another three to four times.
Okay, so we've got it all charged up. Let's go ahead and put it up into the vehicle. We're gonna grab onto these bolts. Make sure they're in decent enough condition. If the threads need to be cleaned up, go ahead and clean them up. The shorter bolt is gonna go up at the top, so we'll go ahead and start that one in, just a few threads.
Moving along to the bottom, at this point, you might notice that the holes just don't line up. If for some reason, the hole for the differential is higher than the shock, that's really not too big of a deal because you could just compress the shock slowly and meet up with the holes. If it's in the other direction, what might you have to do? Maybe you have to jack up a little bit more on the frame or maybe a little bit more on the differential to make it so it matches up. Grab your nut. Start it on there. All right, let's bottom everything out and then torque it down. Go ahead and torque those shock nuts to 59 foot-pounds. Let's do the same to the other.
All right, let's get the wheel up on here. Start on all your lug nuts, bottom them out, and then we'll torque them to 103 foot-pounds. Let's torque these in a crisis cross manner. Now it's gonna be time to put on your center cover. If you were to look at the backside, you're gonna see something that looks a lot like a valve stem. Line that up with your valve stem. Then just give it a nice loving bonk, make sure it's completely secured, take it for a road test.
