Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This parking brake shoe set with hardware is just what you need to get your vehicle stopping in good order again!

Parking Brake Shoe Specifications:

  • 4 Piece Rear Parking Brake Shoe Set
  • Replaces dealer part numbers: 05080568AA, 5080568AB, 5093703AA
  • Direct replacements
  • Professional Grade Shoe Set
  • Correct for models with rear disc brakes

Parking Brake Hardware Specifications:

  • Will service both LH (Driver Side) & RH (Passenger Side) REAR PARKING BRAKES
  • Kit includes:
    • 6 Springs
    • 4 Retainers
    • 4 Pins
    • 2 Adjusters
  • Direct replacements
  • Built to strict quality control standards

This rear parking brake shoe with hardware makes great replacements and have excellent value over the price of the dealer parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:52)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Caliper (2:01)
    • Remove the 21mm bolts from the caliper carrier
    • Secure the caliper bracket and caliper with a bungee chord
  3. step : Removing the Rotor (2:27)
    • If the rotor is frozen, make sure the e-brake shoes are spun down if they're contacting the rotor
    • Tap the rotor from the front with a hammer without damaging the hub's studs
    • Pull the rotor off
  4. step : Removing the Brake Shoes (3:14)
    • Chisel off the rear retaining pin with a hammer and pick
    • Remove the two brake shoe springs with the vise grip pliers, beginning with the bottom
    • Remove the brake adjuster
    • Remove the rear brake shoe from the mechanism at the top
    • Remove the brake shoes
  5. step : Installing the Brake Shoes (5:25)
    • Be sure that the larger, single groove is on the bottom
    • Thread the upper shoe spring into the shoes
    • Place the shoes onto the hub
    • Pry out the shoes and insert them into the mechanism
    • Twist on the front retaining spring with vise grip pliers
    • Put the adjuster into place
    • Insert the lower spring in with vise grip pliers
    • Thread the retaining pin into the brake shoe
    • Lock the pin onto the holder
    • Repeat the steps on the opposite side
  6. step : Reinstalling the Rotor (9:12)
    • Remove surface rust or scaling from the hub with a wire brush
    • Apply brake grease to the hub without touching the studs
    • Insert the rotor into place
    • Apply brakes parts cleaner to the rotor
    • Put your truck in neutral
    • Check that the rotor spins freely - a little resistance is ok
    • Adjust the e-brake shoes with the star wheel if needed
  7. step : Reinstalling the Caliper (11:35)
    • Remove the bungee chord from the caliper
    • Insert the caliper into place
    • Tighten the two 21mm bolts into the caliper bracket
    • Torque the 21mm bolts to 100 foot-pounds
  8. step : Reinstalling the Wheel (12:19)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Brake Parts Cleaner

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 22mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2007-2009Chrysler Aspen Chrysler Aspen Rear Parking Brake Shoe & Hardware Kit
2007-2009Dodge Durango Dodge Durango Rear Parking Brake Shoe & Hardware Kit
2007-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Quad Cab Rear Parking Brake Shoe & Hardware Kit
2007-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Regular Cab Rear Parking Brake Shoe & Hardware Kit
2009-2010Dodge Ram 1500 Truck Dodge Ram 1500 Truck Rear Parking Brake Shoe & Hardware Kit
Part #: 1ABDS00255

Out of Stock

How-to Video:

(13:21 min)