Replaces

Nissan Rogue Complete Strut Assembly & Shock Absorber Kit TRQ SKA61031 - 1ASSP01340

Part Details

  • Quantity: 4 Piece Set

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Direct Fit

Fits and functions correctly.  Competitors combine applications to reduce the amount of parts they carry, resulting in: incorrect vehicle height, poor response and an uncomfortable ride.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Strut Assembly (1:36)
    • Pry off the flexible brake hose from the clip
    • Remove the rubber retainer for the ABS sensor
    • Place locking jaw pliers on the backside of the sway bar link joint
    • Remove the nut with an 18mm socket and ratchet
    • Remove the sway bar link from the strut
    • Remove the 21mm bottom strut bolts
    • Move the spindle out of the strut
    • Remove the rubber cover on the cowl panel
    • Remove the inside 13mm bolts
    • Loosen the last 13mm down to the end of the threads
    • Support the strut without pushing up
    • Lower the strut down and out
    • Leave the bolt in the socket extension
  3. step : Installing the Strut Assembly (5:15)
    • Set the thread into the nut on the new strut on the bolt
    • Set the strut into place
    • Tighten the 13mm bolt
    • Tighten the inside 13mm bolts
    • Reinstall the steering knuckle into the bottom of the strut
    • Tighten the 21mm bolt to the bottom of the strut
    • Clip locking pliers to the back of the sway bar link
    • Tighten the 18mm nut to the sway bar link
    • Reconnect the ABS harness to the hangers
    • Slide the brake hose into place
    • Reinstall the spring clip and tap it in
  4. step : Reattaching the Wheel (8:02)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 18mm Socket
  • 13mm Socket

4.7 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
1
0
0
0
trq strut kit
great price & ride, my mechanic who installed it was impressed with the quality of the whole kit!
September 25, 2018
Purchased
1 month ago
Well pleased with this purchase
All parts looked to be of equal quality to the OEM that they replaced, and fit as expected. Instructional videos were very helpful. Shipping was fast, and free. I saved $950 compared to what my local guy wanted to do this job.
July 13, 2017
Purchased
1 year ago
Shocks and struts
Like the price looked at other auto sites cheapest even with shipping easy to put on good fit for what I wanted to do
March 27, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2008-2011Nissan Rogue Nissan Rogue Front & Rear Complete Strut Assembly & Shock Absorber Kit 4 Piece Set TRQ SKA61031
2012Nissan Rogue Nissan Rogue Front & Rear Complete Strut Assembly & Shock Absorber Kit 4 Piece Set (Built Before 1/12 Production Date) TRQ SKA61031

This part replaces:

  • Monroe 172609
  • Monroe 172608
  • Monroe 37328
  • KYB 349097
  • TRQ SKA61031
  • Monroe 272608
  • Monroe 272609
  • Hollander 527-50527R
  • Hollander 527-50528L
Part #: 1ASSP01340


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SKA61031

How-to Video:

(08:48 min)