Nissan Passenger Side Power Window Motor Dorman 742-510 - 1AWPM00175

This power window motor is just what you need to get your vehicle in good shape again! If your window regulator is good, but the motor is burned out, then this is the part for you.

Specifications:

• RH (Passenger Side) FRONT or REAR as listed by application
• Brand New
  • No core charge
• Replaces dealer part numbers: 80730-4Z305, 80730-8991A, 80730-8991D, 80730-EA005, 82730-3Z005, 82730-7Z805, 807304Z305, 807308991A, 807308991D, 80730EA005, 827303Z005, 827307Z805
• Direct replacement
• Built to strict quality control standards

This window motor makes a great replacement and has good cost savings over a dealer unit.

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

step : Removing the Door Panel (1:14)

• Use a flat blade screwdriver to pry off the bezel inside the door pull
• Use a flat blade screwdriver to pry off the bezel inside the door handle
• Remove the Phillips head screw inside the door handle
• Remove the Phillips head screw inside the door pull
• Remove the three Phillips head screws alongside the bottom of the door panel
• Remove the Phillips head screw at the back of the door panel
• Pull off the mirror base trim
• With a putty knife pry off the door panel
• Disconnect the door lock wiring harness
• Disconnect the latch rod from the door handle
• Disconnect the power window switch wiring harness
• If any pins remain in the door, remove them with needle nose pliers
• Reinstall those pins into the door panel

step : Removing the Window Regulator (3:34)

• Carefully pull back the water shield, avoiding tearing it
• Remove the six 10mm nuts that hold the regulator to the door
• Pull the window down partially by hand
• Loosen the two 10mm nuts on the window track
• Remove the window from the window track
• Pull the window up by hand
• Pull the window regulator partially out
• Disconnect the window motor wiring harness

step : Detaching the Window Motor from the Window Regulator (6:46)

• Remove the three T25 Torx screws that hold the motor to the regulator
• Detach the motor from the regulator

step : Attaching the New Motor to the Regulator (7:24)

• Line up the motor and regulator gears
• Push the motor into place
• Start the three screws by hand
• Tighten the three T25 Torx screws

step : Reattaching the Window Regulator (8:06)

• Connect the window motor to its wiring harness
• Connect the window switch to its wiring harness
• Turn the regulator down slightly, using the window switch
• Insert the regulator into the door
• Put the regulator into place
• Start all the nuts and bolts by hand
• Tighten all the nuts and bolts
• Move the regulator into place with the window switch
• Disconnect the wiring harness from the window switch
• Slide the window onto the window track
• Tighten the 10mm nuts on the window track
• Carefully put the water shield back into place

step : Reinstalling the Door Panel (11:11)

• Reconnect the wiring harness to the window switch
• Check that the window regulator and motor function properly
• Reconnect the door lock switch
• Clip the latch rod to the door handle
• Slide the door panel into place
• Push the door panel locating tab into its hole
• Push the pins in
• Insert the Phillips screw into the door pull
• Insert the Phillips screw into the door handle
• Insert the three Phillips screws along the bottom of the door panel
• Insert the Phillips screw at the back of the door panel
• Push the mirror base trim back into place
• Put the bezel back into the door handle
• Put the bezel back into the door pull