Replaces

Nissan Driver Side Power Window Motor Dorman 742-509 - 1AWPM00174

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This power window motor is just what you need to get your vehicle in good shape again! If your window regulator is good, but the motor is burned out, then this is the part for you.

Specifications:

  • LH (Driver Side) FRONT or REAR as listed by application
  • Brand New
    • No core charge
  • Replaces dealer part numbers: 80731-4Z305, 80731-8991A, 80731-8991D, 80731-EA005, 82731-3Z005, 82731-7Z805, 807314Z305, 807318991A, 807318991D, 80731EA005, 827313Z005, 827317Z805
  • Direct replacement
  • Built to strict quality control standards

This window motor makes a great replacement and has good cost savings over a dealer unit.

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Door Panel (1:14)
    • Use a flat blade screwdriver to pry off the bezel inside the door pull
    • Use a flat blade screwdriver to pry off the bezel inside the door handle
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw inside the door pull
    • Remove the three Phillips head screws alongside the bottom of the door panel
    • Remove the Phillips head screw at the back of the door panel
    • Pull off the mirror base trim
    • With a putty knife pry off the door panel
    • Disconnect the door lock wiring harness
    • Disconnect the latch rod from the door handle
    • Disconnect the power window switch wiring harness
    • If any pins remain in the door, remove them with needle nose pliers
    • Reinstall those pins into the door panel
  2. step : Removing the Window Regulator (3:34)
    • Carefully pull back the water shield, avoiding tearing it
    • Remove the six 10mm nuts that hold the regulator to the door
    • Pull the window down partially by hand
    • Loosen the two 10mm nuts on the window track
    • Remove the window from the window track
    • Pull the window up by hand
    • Pull the window regulator partially out
    • Disconnect the window motor wiring harness
  3. step : Detaching the Window Motor from the Window Regulator (6:46)
    • Remove the three T25 Torx screws that hold the motor to the regulator
    • Detach the motor from the regulator
  4. step : Attaching the New Motor to the Regulator (7:24)
    • Line up the motor and regulator gears
    • Push the motor into place
    • Start the three screws by hand
    • Tighten the three T25 Torx screws
  5. step : Reattaching the Window Regulator (8:06)
    • Connect the window motor to its wiring harness
    • Connect the window switch to its wiring harness
    • Turn the regulator down slightly, using the window switch
    • Insert the regulator into the door
    • Put the regulator into place
    • Start all the nuts and bolts by hand
    • Tighten all the nuts and bolts
    • Move the regulator into place with the window switch
    • Disconnect the wiring harness from the window switch
    • Slide the window onto the window track
    • Tighten the 10mm nuts on the window track
    • Carefully put the water shield back into place
  6. step : Reinstalling the Door Panel (11:11)
    • Reconnect the wiring harness to the window switch
    • Check that the window regulator and motor function properly
    • Reconnect the door lock switch
    • Clip the latch rod to the door handle
    • Slide the door panel into place
    • Push the door panel locating tab into its hole
    • Push the pins in
    • Insert the Phillips screw into the door pull
    • Insert the Phillips screw into the door handle
    • Insert the three Phillips screws along the bottom of the door panel
    • Insert the Phillips screw at the back of the door panel
    • Push the mirror base trim back into place
    • Put the bezel back into the door handle
    • Put the bezel back into the door pull

Tools needed for replacement:

    General Tools

  • Flashlight
  • Putty Knife

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Door Panel Removal Tool

  • Star Drivers & Sockets

  • T30 Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2002-2006Nissan Altima Nissan Altima Rear Driver Side Power Window Motor
2005-2009Nissan Frontier Nissan Frontier Front Driver Side Power Window Motor
2003-2007Nissan Murano Nissan Murano Rear Driver Side Power Window Motor
2000-2005Nissan Sentra Nissan Sentra Front Driver Side Power Window Motor
2000-2004Nissan Xterra Nissan Xterra Rear Driver Side Power Window Motor
2005-2009Nissan Xterra Nissan Xterra Front Driver Side Power Window Motor
Only 3 left in stock
Part 1AWPM00174
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Dorman
Brand #: 742-509