This replacement front suspension kit is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a SET of 4
    • (2) - FRONT Strut and Spring Assemblies - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Stabilizer Bar Links - LH (Driver Side) & RH (Passenger Side)
  • Strut and spring assemblies include:
    • Upper Mounts
    • Upper Spring Isolators
    • Upper Spring Seats
    • Boot Kits
    • Lower Spring Isolators
    • Struts
  • Direct replacements
  • Built to strict quality control standards

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Accessing the Strut (0:53)
    • Remove the lug nuts
    • Pull the wheel free
    • Apply penetrating oil to the bolt holding the lower strut and the upper bolt holding the stabilizer link
    • Remove the clip holding the brake hose to the strut (Use a screwdriver to pry up from below)
    • Pull the hose free
    • Lock locking pliers on the backside of the stabilizer shaft
    • Remove the 14mm bolt
    • Spray the 17mm bolt holding the steering knuckle to the strut with penetrating oil
    • Remove the 17mm bolt using the pipe for extra leverage
  2. step : Removing the Strut (3:11)
    • Spray penetrating oil around the bottom of the strut
    • Hit the steering knuckle with a sledge hammer
    • Once the knuckle moves, place a piece of wood over the knuckle and hammer the rest of the way
    • Remove two of the bolts holding the strut from the back of the engine. Loosen the third bolt
    • Push down on the steering knuckle and push the bottom free
    • Remove the third screw up top to free the strut
  3. step : Replacing the Strut (4:29)
    • Line the strut up with the bolt holes up top. Replace the three bolts firm but not fully tightened
    • Spray penetrating oil on the strut and steering knuckle
    • Once its lined up but a jack underneath the knuckle and use it to force it into place
    • Replace the bolt holding the knuckle to the strut. (Use a torque wrench to tighten it to 80 ft/lbs)
    • Bring the hose down and feed it through into place. Replace the clip
    • Reconnect the stabilizer link. Using locking pliers on the back, thread the nut on and tight to 50-60 ft/lbs
    • Replace the wheel
    • Replace lug nuts, and tighten to 100 ft/lbs. in a star pattern
    • Tighten the upper strut bolts to 25ft/lbs

Tools needed for replacement:

    General Tools

  • Sledge Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 15mm Socket
  • 13mm Socket
  • 16mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(07:42 min)

Tools List:

    General Tools

  • Sledge Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 15mm Socket
  • 13mm Socket
  • 16mm Socket



This part replaces:

  • Monroe 172264
  • Monroe 172263
  • Moog K80235
  • OE # 31351095695, 31351091496

Vehicle Fit

  • 2004-2009 Mazda 3 Front Suspension Kit 4 Piece Set excluding Speed Model
  • 2006-2010 Mazda 5 Front Suspension Kit 4 Piece Set
Part #: 1ASFK01954

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More