Replaces

Infiniti G35 Nissan 350Z Steering & Suspension Kit - 1ASFK05804

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Rearward Control Arms with Ball Joints
  • Quantity: 12 Piece Set
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Lower Forward Control Arms
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (2) Steering Rack & Pinion Bellows
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:55)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:15)
    • Measure the distance from the end of the boot to the center of the top of the tie rod
    • Note that measurement
    • Apply penetrating oil to the tie rod lock nut
    • Hold the inner tie rod with a 13mm wrench
    • Loosen the locking nut with an adjustable wrench
    • Turn the wheel by hand or with the steering wheel for better access to the tie rod
    • Remove the cotter pin with needle nose pliers
    • If you cannot remove the cotter pin, sheer it off by removing the 19mm bolt
    • Remove the 19mm bolt
    • Loosen the tie rod from the spindle by striking the spindle with a hammer
    • Pull the outer tie rod out of the handle
    • Hold the inner tie rod with a 13mm wrench
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (3:52)
    • Apply anti-seize grease to the inner tie rod
    • Hold the inner tie rod with a 13mm wrench
    • Twist the outer tie rod on by hand
    • Measure the distance from the end of the boot to the center of the top of the tie rod
    • This should equal the measurement recorded in Step 2
    • Push the outer tie rod into the spindle
    • Start the tie rod nut by hand
    • Tighten the nut to 55 foot-pounds of torque
    • Line the tie rod hole up with one of the slots in the nut
    • Insert the cotter pin and bend it to lock it
    • Hold the inner tie rod with a 13mm wrench
    • Tighten the locking nut with an adjustable wrench
  4. step : Reattaching the Wheel (6:35)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large Hammer

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Lug Wrench
  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 13mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Perfect
Everything fit perfectly. Quality seems to be very good. Parts from Taiwan not china.
May 23, 2018
Purchased
2 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2007 Infiniti G35 Coupe Rear Wheel Drive Steering & Suspension Kit 12 Piece Set
  • 2006 Nissan 350Z (Built After 2/06 Production Date) Steering & Suspension Kit 12 Piece Set
  • 2007-2009 Nissan 350Z Steering & Suspension Kit 12 Piece Set

This part replaces:

  • Hollander 511-58200R
  • Hollander 511-58201L
  • Hollander 512-58685R
  • Hollander 512-58686L
  • Hollander 512-58883R
  • Hollander 512-58884L
  • Hollander 512-58916R
  • Hollander 512-58917L
  • OE # 48520AM625
  • OE # 48521AL525
  • OE # 48521AL685
  • OE # 48640AL585
  • OE # 54468CD00C
  • OE # 54469CD00C
  • OE # 54500AM602
  • OE # 54501AM602
  • OE # 54524AL500
  • OE # 54524CF00A
  • OE # 54525AL500
  • Dorman 521-601
  • Dorman 521-602
  • Dorman 521-603
  • Dorman 521-604
  • Dorman 521-605
  • Dorman 521-606
  • Moog ES80578
  • Moog ES80579
  • Moog EV80279
  • Moog K621372
  • Moog K621373
  • Moog K621690
  • Moog K621936
  • Moog K642008
  • Moog K642009
  • Beck Arnley 101-6041
  • Beck Arnley 103-3071
  • Beck Arnley 103-3072
Part #: 1ASFK05804

How-to Video:

(07:13 min)