1AIMX00183-Ignition Lock Cylinder


Ignition Lock Cylinder Dorman 924-716

Save 22%
List: $97.95 Save: $22.00
Part 1AIMX00183
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Brand #: 924-716

Frequently bought together

Vehicle Fit
Warranty & Shipping
How-To & Tools

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Cadmium and Cadmium Compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Disconnecting the Battery (0:43)
    • Disconnect the negative battery cable with a 10mm socket and ratchet
  2. step : Accessing the Ignition Lock Cylinder (1:03)
    • Raise the steering wheel
    • Remove the two 7mm or T25 Torx screws from the bottom dash panel
    • Pull down the lower dash panel
    • Remove the T25 screw from the bottom of the steering wheel
    • Pull off the lower steering column panel
    • Pull off the upper steering column panel
  3. step : Removing the Lock Cylinder (2:02)
    • Disconnect the ignition electrical connection at the top
    • Insert the key into the lock cylinder
    • Turn the key to the on position
    • Press a pick or awl into the lock cylinder hole
    • Remove the lock cylinder
  4. step : Preparing the New Lock Cylinder (2:21)
    • Apply white grease to the old lock cylinder tumblers
    • Pry off the tumbler retainers with a pick
    • Prepare a diagram of the lock
    • Pull out the first tumbler
    • Put it in the first position on the diagram
    • Pull out each subsequent tumbler, putting it in position on the diagram
    • If you are replacing an old style cylinder with a new style cylinder, omit the first tumbler from the diagram
    • Put a spring into the first tumbler slot on the new lock cylinder
    • Check the number on the next tumbler
    • Insert a tumbler with the same number into the corresponding tumbler of the new lock cylinder
    • For each subsequent tumbler, put in a spring and a tumbler whose number matches the corresponding tumbler from the old lock cylinder
    • Insert the key into the new lock cylinder to test it
    • Apply white grease to the new lock cylinder
  5. step : Installing the New Lock Cylinder (7:23)
    • Push the lock cylinder into place with the groove fitting into the steering column groove
    • Connect the ignition electrical connection
  6. step : Reconstructing the Steering Column (7:41)
    • Put on the upper steering column panel
    • Put on the lower steering column panel
    • Clip the steering column panels together
    • Insert the T25 Torx screw into the steering column
    • Push on the lower dash panel
    • Insert the two 7mm or T25 screws into the lower dash panel
  7. step : Reconnecting the Battery (8:05)
    • Reconnect the negative battery cable with a 10mm socket and ratchet

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil
  • White Grease

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Bent Tipped Awl

  • Star Drivers & Sockets

  • T25 Driver

Fits the following Makes:

Year Make Model Description
2005Buick Century Buick Century Ignition Lock Cylinder
2005-2009Buick LaCrosse Buick LaCrosse Ignition Lock Cylinder
2009-2011Buick Lucerne Buick Lucerne Ignition Lock Cylinder
2007-2008Cadillac DTS Cadillac DTS Ignition Lock Cylinder
2007-2014Cadillac Escalade Cadillac Escalade Ignition Lock Cylinder
2007-2014Cadillac Escalade ESV Cadillac Escalade ESV Ignition Lock Cylinder
2007-2013Cadillac Escalade EXT Cadillac Escalade EXT Ignition Lock Cylinder
2004-2009Cadillac SRX Cadillac SRX Ignition Lock Cylinder
2007-2013Chevrolet Avalanche Chevrolet Avalanche Ignition Lock Cylinder
2008-2014Chevrolet Express 1500 Van Chevrolet Express 1500 Van Ignition Lock Cylinder
2008-2014Chevrolet Express 2500 Van Chevrolet Express 2500 Van Ignition Lock Cylinder
2008-2014Chevrolet Express 3500 Van Chevrolet Express 3500 Van Ignition Lock Cylinder
2006-2013Chevrolet Impala Chevrolet Impala Ignition Lock Cylinder
2014-2016Chevrolet Impala Limited Chevrolet Impala Limited Ignition Lock Cylinder
2006-2007Chevrolet Monte Carlo Chevrolet Monte Carlo Ignition Lock Cylinder
2007Chevrolet Silverado 1500 Chevrolet Silverado 1500 with New Body Style Ignition Lock Cylinder
2008-2013Chevrolet Silverado 1500 Chevrolet Silverado 1500 Ignition Lock Cylinder
2007Chevrolet Silverado 2500 HD Chevrolet Silverado 2500 HD with New Body Style Ignition Lock Cylinder
2008-2014Chevrolet Silverado 2500 HD Chevrolet Silverado 2500 HD Ignition Lock Cylinder
2007Chevrolet Silverado 3500 HD Chevrolet Silverado 3500 HD with New Body Style Ignition Lock Cylinder
2008-2014Chevrolet Silverado 3500 HD Chevrolet Silverado 3500 HD Ignition Lock Cylinder
2007-2014Chevrolet Suburban 1500 Chevrolet Suburban 1500 Ignition Lock Cylinder
2007-2013Chevrolet Suburban 2500 Chevrolet Suburban 2500 Ignition Lock Cylinder
2007-2014Chevrolet Tahoe Chevrolet Tahoe Ignition Lock Cylinder
2005-2006Chevrolet Uplander Chevrolet Uplander with Large Z-Groove Head Key without Winged Bezel Ignition Lock Cylinder
2008-2014GMC Savana 1500 Van GMC Savana 1500 Van Ignition Lock Cylinder
2008-2014GMC Savana 2500 Van GMC Savana 2500 Van Ignition Lock Cylinder
2008-2014GMC Savana 3500 Van GMC Savana 3500 Van Ignition Lock Cylinder
2007GMC Sierra 1500 GMC Sierra 1500 with New Body Style Ignition Lock Cylinder
2008-2013GMC Sierra 1500 GMC Sierra 1500 Ignition Lock Cylinder
2007GMC Sierra 2500 HD GMC Sierra 2500 HD with New Body Style Ignition Lock Cylinder
2008-2014GMC Sierra 2500 HD GMC Sierra 2500 HD Ignition Lock Cylinder
2007GMC Sierra 3500 HD GMC Sierra 3500 HD with New Body Style Ignition Lock Cylinder
2008-2014GMC Sierra 3500 HD GMC Sierra 3500 HD Ignition Lock Cylinder
2007-2014GMC Yukon GMC Yukon Ignition Lock Cylinder
2007-2014GMC Yukon XL 1500 GMC Yukon XL 1500 Ignition Lock Cylinder
2007-2013GMC Yukon XL 2500 GMC Yukon XL 2500 Ignition Lock Cylinder
2008-2009Hummer H2 Hummer H2 Ignition Lock Cylinder

Part Interchange

Brand Label Part Number
DIY Solutions BSS00281

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Brand #: 924-716
Product Reviews
4.74/ 5.0 19
19 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Great product
April 20, 2018
Very easy to install. Came with good instructions. My local dealer was going to charge me tons for this part. But this was very simple to do my self.
My key turns now!
July 30, 2018
My ignition cylinder switch wore out. I found many advertisements for replacement cylinders but 1A Auto had the goods to tumble the lock so I could continue to use the same key. The parts ordered and the installation video were perfect. Thanks 1A Auto!
Ignition lock cylinder
July 31, 2018
Wasn't confident I could rekey the cylinder myself. Took it to locksmith for $25. Putting it in was a breeze. Quality products. A1 is my go to for parts.
key cylinder wont turn
October 9, 2018
The key cylinder in my 2008 Silverado was getting so bad I was afraid it would not turn on. I found a utube vid showing how to rebuild it so you can keep your original key and not have to go thru replacing door locks and spare tire lock. They recommended this place to get the stuff I needed. I got a new cylinder and all the tumblers to key it to my old original key. It was simple cheap and it works great. They send instructions with it. I highly recommend this. There is no programming the keys or anything. Follow the instructions and go.....great product and great company.
November 13, 2018
Came with instructions that was easy to follow. Delivery was fast.
Just what I needed!
November 15, 2018
My 2008 Silverado 2500HD was to the point that sometimes I could not get the key to get the key to turn the ignition switch. I had never replaced and ignition lock cylinder before so was a little reluctant to try. I was the video on 1A Auto and decided to give it a try. It was no problem at all. I would highly recommend this if are having a problem with your key not turning the ignition cylinder. Thanks 1A!!!
Ignition switch
March 6, 2019
Very pleased. Instructions were easy to follow. Part fit perfectly. Will use this company for buying more parts.
April 14, 2019
I bought this key cylinder for my pickup I am a mechanic by trade and followed the instructions to the T. but it did not work. 1A auto told me they would send a replacement. " I AM STILL WAITING FOR IT"
Perfect replacement ignition cylinder for 2007 GMC sierra
May 2, 2019
Worked perfectly. Instructions easy to follow, took about 20 minutes with double and triple checking everything. Truck starts great.
Great product!
July 5, 2019
I never knew this could be done. This product was super easy to replace. Thanks to the great video from 1A Auto. Works absolutely amazing.
August 18, 2019
This part works great easy to code would recommend to others with key switch problems . Works great with my key
Great Product
September 15, 2019
Instructions were super easy to follow! Saved at least $400 from the dealership
Great Product!!
October 9, 2019
Product looked identical to the OEM cylinder I pulled out. Using the available on line videos rekeying the new one to my current key was a breeze. Best of all it fired up when I turned the key!!! Price was very reasonable as well.
Excellent product and huge savings over dealer repair
November 15, 2019
The ignition key on my 2011 GMC Sierra was getting worse and refusing to turn without a lot of fiddling. If I had not watched the 1A Auto video I would never have been able to do this repair, which seems intimidating with the small parts on the key cylinder, but actually is simpler than it looks if you carefully follow the instructions step by step. No need to reprogram the truck since you are re-using the original key with a new lock cylinder and tumblers to match the old key. I cannot imagine what the GM dealer would charge for parts and labor for this job. Very pleased.
Easy Install
December 12, 2019
I had never replaced an ignition lock cylinder or re-coded tumblers before, yet it turned out to be extremely easy and took maybe 20 minutes total. I was so worried that I would mess up on the tumblers, but it was one of the easiest vehicle fixes ever. Don't let inexperience with tumblers keep you from buying. And don't forget to unhook the negative battery cable.
Exact fit. Problem solved.
April 2, 2020
I never replaced lock tumblers for a vehicle before. I watched the “how to remove key cylinderâ€� video tutorial on 1aauto.com. for my Chevy Silverado. It was spot on accurate. I ordered a new cylinder and the instructions that came with it were easy to follow. I must have saved at least $300 by doing it myself. There are other vendors that have this cylinder for less money. I figured I helped pay for some of the labor costs that goes into making the help videos! It’s all good! Thank you!
worked great!!
May 8, 2020
arrived right on time, easy to put together, great product fixed my ignition key turning problem!
Easy fix
July 18, 2020
Fixed the problem of key not turning at times on my 2008 Silverado.Very easy to do,probably took just over an hour total.
Worked great no problems
August 23, 2020
Worked great no problems
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Where is the key? Does it come with this?
April 16, 2018
no key. You key it to your existing one. I got this and it worked great. easy to set pins. just use your existing one and match it up.
April 16, 2018
It does not come with the key. It's just the mechanical part that is mounted inside the ignition switch. If you need a new key, you can probably talk to your local car dealership. if you still have the original key or any duplicate keys, they should still work in the new cylinder as it is specific to a particular, make, model and year.
April 16, 2018
No it doesn't come with a key. You have to set up the tumbler with the old one and use your original key.
April 16, 2018
You use your old key. When you take the old lock cylinder out, you set up the new lock cylinder just like the old cylinder. That way your old key works.
April 16, 2018
Carjacked. Keys out there. Have tried to take again. If I get this and another cut key. Does that key need to be programmed in some way and how?
April 30, 2018
Hello! According to our specifications this product comes with a tumbler to program to the original key(s).
April 30, 2018
What would cause my engine to try to start when SHUTTING OFF THE KEY???
November 27, 2018
There could be multiple reasons why you're having this particular problem. We suggest taking your vehicle to a nearby reputable shop to identify the cause. Once you know the cause, we'll be happy to see if we carry the parts and how-to videos needed for your repair.
November 27, 2018
My key broke in half and my son lost the other half so is it still possible for myself diy dad to change it out and if so how do I do it ??? Thank you
July 7, 2020
Thanks for your inquiry. Written and video installation instructions are found on the product page under the "How-To & Tools" tab. The video for this repair can be found here: https://youtu.be/3DKNx7im76s We're constantly adding new installation video instructions. If we do not have one for your vehicle on the product listing page, please check again at a later time or check our Video Library to see similar repairs here: https://www.1aauto.com/videos
July 7, 2020
Customer service


Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

Ignition Lock Cylinder Dorman 924-716-1AIMX00183 does not fit your:

Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.