The ignition coil is a crucial part of your ignition system. It's function is to convert the 12 volt power of your vehicle's electrical system in to 35,000 or more volts. This produces a high intensity spark at the spark plug which then ignites the fuel in the cylinder. Coils in general will wear out over time. This will cause a misfire condition.

Specifications:

  • Brand New Ignition Coil
  • Built to strict quality control standard
  • Direct replacement
  • 100% factory tested

This coil is for a distributorless application. Sold as a EACH. Replace individually as needed.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function properly for your specific application.

Optimum Performance

Optimal performance, TRQ ignition coils are designed to meet or exceed the requirements of the vehicle.  TRQ ignition coils provide the correct primary and secondary resistance, voltage output, and spark energy that the vehicle needs to restore to its original operating condition.

Premium Quality

Manufactured with quality components and materials by using advanced technology to meet the highest quality control standards in the industry.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wiper Arms (0:25)
    • Pry the cap off the driver side wiper arm stud
    • Remove the 14mm nut from the stud
    • Pull the wiper arm off the stud
    • Open the hood
    • Remove the two 14mm mounting nuts from the passenger side wiper arm
    • Pull the wiper arm off the windshield
  2. step : Removing the Cowl Cover (2:10)
    • Pry off the two cowl corner trim pieces with a trim tool
    • Pry the two push clips out of each side of the cowl with a flat blade screwdriver
    • Release the clips along the front of the cowl
    • Lift the cowl up and out of the engine bay
  3. step : Removing the Wiper Transmission (3:41)
    • Unplug the wiper motor electrical connector
    • Unclip the wiring harness from the lower wiper cowl
    • Remove the four 10mm bolts from the wiper transmission
    • Pull the wiper transmission off the lower wiper cowl
  4. step : Removing the Lower Cowl (5:01)
    • Remove the three 10mm bolts from the lower cowl bracket
    • Remove the bracket from the cowl
    • Remove the nine 10mm bolts from the lower cowl
    • Pull the cowl out of the engine bay
  5. step : Removing the Ignition Coils (6:04)
    • Remove the plastic engine cover
    • Disconnect the wiring harnesses
    • Remove the 10mm bolt from the coil pack
    • Lift the coil pack up and out
  6. step : Installing the Ignition Coils (7:04)
    • Insert the coil into place
    • Tighten the 10mm bolt to the coil
    • Connect the wiring harness
    • Press the engine cover on
  7. step : Installing the Lower Cowl (11:10)
    • Fold over the cowl wind guides
    • Slide the lower cowl into place
    • Insert the nine 10mm bolts into the cowl
    • Raise the cowl wind guides
    • Line up the support bracket on the cowl
    • Insert the three 10mm bolts into the support bracket
  8. step : Installing the Wiper Transmission (10:23)
    • Line up the wiper transmission
    • Insert the wiper transmission pin into the rubber grommet
    • Insert the four 10mm bolts into the wiper transmission
    • Plug in the wiper motor electrical connector
    • Clip the wiring harness to the lower wiper cowl
  9. step : Installing the Cowl Cover (11:56)
    • Slide the cowl under the windshield
    • Push in the clips along the front of the cowl
    • Insert the two push clips into each side of the cowl
    • Clip the corner trim piece onto each side of the cowl
  10. step : Installing the Wiper Arms (12:59)
    • Line up the passenger side wiper arm on the windshield
    • Fasten the two 14mm nuts onto the wiper arm
    • Line up the driver side wiper arm on its stud
    • Fasten the 14mm nut onto the stud
    • Push the cap onto the wiper stud
    • Close the hood

Tools needed for replacement:

    Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 10mm Socket

  • Sockets - SAE

  • 9/16 Inch Spark Plug Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Perfict fit at a great price.
The listing made it clear which coil would fit. I was afraid it wouldn't
work because of the low price, but it's great.
March 4, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2011-2016 Lexus CT200h Ignition Coil
  • 2009-2010 Pontiac Vibe Ignition Coil L4 1.8L
  • 2008-2014 Scion xD Ignition Coil
  • 2009-2016 Toyota Corolla Ignition Coil L4 1.8L
  • 2009-2014 Toyota Matrix Ignition Coil L4 1.8L
  • 2010-2015 Toyota Prius Ignition Coil
  • 2012-2016 Toyota Prius V Ignition Coil

This part replaces:

  • OE # 9091902258
  • Hollander 610-50162
  • OE # 9091902252
  • Standard Motor Products UF596
Part #: 1AECI00255

How-to Video:

(14:07 min)