Replaces

2010 Dodge Journey V6 3.5L Ignition Coil

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

The ignition coil is a crucial part of your ignition system. It's function is to convert the 12 volt power of your vehicle's electrical system in to 35,000 or more volts. This produces a high intensity spark at the spark plug which then ignites the fuel in the cylinder. Coils in general will wear out over time and cause a misfire condition. In engines like this that use a coil, if the coil goes bad, the complete assembly needs to be replaced.

This Ignition Coil features the following specifications:

  • New not remanufactured
  • Replaces dealer part number: 4606869AA, 4606869AB, 4606869 AA, 4606869 AB
  • Built to strict quality control standards
  • Direct replacement
  • 100% factory tested

 

This is an electrical part and is tested before it leaves our manufacturer.

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Direct Fit Replacement

Guaranteed to fit and function properly for your specific application.

Optimum Performance

Meets or exceeds requirements of the vehicle. Provides the correct primary and secondary resistance, voltage output, and spark energy needed to restore original operating condition.

Premium Quality

Manufactured with quality materials to meet highest quality control standards in the industry.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing Ignition Coils 2 and 4 (1:01)
    • Open the hood
    • Disconnect the ignition coil wiring harnesses
    • Remove the 10mm bolt from each ignition coil
    • Pull each ignition coil up and out
  2. step : Installing Ignition Coils 2 and 4 (Installing Ignition Coils 2 and 4)
    • Put the ignition coils into place
    • Connect the ignition coil wiring harnesses
    • Insert the 10mm bolt for each ignition coil
  3. step : Removing the Upper Intake Manifold (3:31)
    • Loosen the throttle body hose clamp with a flat blade screwdriver
    • Pull the coolant line out of the intake hose
    • Pull the intake hose off the throttle body
    • Remove the sensor from the intake hose
    • Disconnect the two hoses from the intake manifold
    • Disconnect the MAP sensor from the top of the intake manifold
    • Disconnect the two writing harness from the intake control valves at the front of the intake manifold
    • Disconnect the wiring harness from the throttle body
    • Remove the two 10mm nuts from the throttle body
    • Remove the seven 10mm bolts from the center of the intake manifold
    • Remove the two 10mm bolts from the manifold brackets
    • Remove the two 15mm bolts from the bottom of the throttle body bracket
    • Remove the bracket from the throttle body
    • Remove the two 15mm bolts from the manifold brackets
    • Pull off the intake manifold
    • Put paper towels into the intake manifold to keep out debris
  4. step : Removing the Remaining Ignition Coils (6:57)
    • Disconnect the ignition coil wiring harnesses
    • Remove the 10mm bolt from each ignition coil
    • Pull each ignition coil up and out
  5. step : Installing the Remaining Ignition Coils (7:18)
    • Put the ignition coils into place
    • Connect the ignition coil wiring harnesses
    • Insert the 10mm bolt for each ignition coil
  6. step : Installing the Upper Intake Manifold (7:38)
    • Remove the paper towels from the intake manifold
    • Clean the intake manifold surface with brake cleaner
    • Connect the PCV breather hose to the back of the valve cover
    • Remove the old gasket from the upper intake manifold with a pick
    • Press in the new intake manifold gasket
    • Remove the old EGR seal
    • Push on the new EGR seal
    • Put the upper intake manifold into place
    • Click the automatic transmission dipstick into place
    • Start the 10mm bolts for the manifold
    • Tighten the seven 10mm bolts in the center of the manifold to 9 foot-pounds, starting at the center
    • Connect the MAP sensor to the manifold
    • Connect the wiring harnesses for the two intake control valves
    • Put the manifold brackets into place
    • Insert the two 15mm bolts into the brackets
    • Insert the two 10mm bolts into the brackets
    • Connect the PCV hose to the manifold
    • Connect the two hoses to the manifold
    • Connect the throttle body wiring harness
    • Put the throttle body bracket into place
    • Start the two 10mm nuts onto the top of the throttle body bracket
    • Insert the two 15mm bolts into the bottom of the bracket
    • Tighten the two 10mm nuts onto the bracket
    • Push the intake hose onto the throttle body
    • Tighten the intake hose clamp with a flat blade screwdriver
    • Snap the coolant line into the intake hose bracket
    • Connect the MAP sensor to the intake hose
    • Push the intake hose onto intake tube if you disconnected them
    • Tighten the intake tube clamp with a flat blade screwdriver

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Gloves
  • Brake Parts Cleaner
  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Wrenches - Metric

  • Complete Metric Wrench Set

4.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
1
0
0
0
Review for my part ordered
My order was delivered quick and was in good condition. The part works amazing as well. Over all I am a satisfied customer.
January 8, 2019
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2006-2010Chrysler 300 Chrysler 300 V6 3.5L Ignition Coil
2006-2010Chrysler 300 Chrysler 300 V6 2.7L Ignition Coil
2007-2008Chrysler Pacifica Chrysler Pacifica V6 4.0L Ignition Coil
2006-2010Chrysler Sebring Chrysler Sebring V6 2.7L Ignition Coil
2007-2010Chrysler Sebring Chrysler Sebring V6 3.5L Ignition Coil
2008-2010Chrysler Town & Country Chrysler Town & Country V6 4.0L Ignition Coil
2008-2010Dodge Avenger Dodge Avenger V6 3.5L Ignition Coil
2008-2010Dodge Avenger Dodge Avenger V6 2.7L Ignition Coil
2009-2010Dodge Challenger Dodge Challenger V6 3.5L Ignition Coil
2006-2010Dodge Charger Dodge Charger V6 2.7L Ignition Coil
2006-2010Dodge Charger Dodge Charger V6 3.5L Ignition Coil
2008-2010Dodge Grand Caravan Dodge Grand Caravan V6 4.0L Ignition Coil
2009-2010Dodge Journey Dodge Journey V6 3.5L Ignition Coil
2006-2008Dodge Magnum Dodge Magnum V6 2.7L Ignition Coil
2006-2008Dodge Magnum Dodge Magnum V6 3.5L Ignition Coil
2007-2011Dodge Nitro Dodge Nitro V6 4.0L Ignition Coil
2006Dodge Stratus Dodge Stratus L4 2.7L Ignition Coil
2009-2010Volkswagen Routan VW Routan V6 4.0L Ignition Coil
Part 1AECI00200
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Dodge is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Dodge or FCA US LLC. See all trademarks.