TRQ ignition coils will have your engine running like new. TRQ ignition coils are manufactured to precise specifications using premium raw materials to optimize each vehicle's ignition system. To ensure peak performance, TRQ recommends replacing ignition coils in sets to prevent electrical output imbalances. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
High dielectric epoxy and reinforced bobbins for extended service life
Rubber, Silicone, or Phenolic Resin Shell: Prevents premature boot wear
Application Specific Design: No modifications required
The ignition coil pack is a crucial part of your ignition system. It's function is to convert the 12 volt power of your vehicle's electrical system in to 35,000 or more volts. This produces a high intensity spark at the spark plug which then ignites the fuel in the cylinder. Coils in general will wear out over time.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Ignition Coil 1999-2004 GMC Sierra 2500
How To Replace Spark Plugs 2000-06 Chevy Tahoe
How To Replace Spark Plugs 2000-06 Chevy Tahoe
How to Replace Ignition Coils 2000-06 GMC Yukon
How to Replace Ignition Coil 2003-2021 Chevrolet Express
How to Replace Ignition Coil 2003-04 GMC Envoy XL
How to Replace Ignition Coils 1999-2007 Chevy Silverado
How to Replace Ignition Coil 2000-06 Chevy Suburban
Created on:
Tools used
7mm Socket
Ratchet
1. Remove the ignition coil
Unbolt the ignition coil
Disconnect the wiring connector.
2. install the new ignition coil
Bolt the ignition coil down.
Connect the wiring connector.
Brought to you by 1AAuto.com. Your source for quality replacement parts and the best service on the internet. In this video we're going to replace an ignition coil on this 2002 GMC Sierra with a 6 liter Vortec V8. This procedure is the same for most of the 4.8, 5.3, and 6.0 liter Vortecs in the trucks as well as the SUV's, very simple, only tool you'll need is a 7 mm socket with a ratchet and extension.
The coils on this GM V8's is pretty easy to get to. There's four of them each side, eight total, one for each cylinder. They're right up here on top. I'm going to do this one because it's just the easiest one to see and film. They're all really easy to get to though. Now, there's a harness that goes in right here. I'm going to pull back on that tab and pull up and the front wire is right down here. You twist it. Hold down. Now you can see the two 7 mm bolts on each side holding it in. One here and one there. We'll just speed it up as we're removing those two 7 mm bolts with a socket and a ratchet and an extension. Our original coil, the new one from 1A Auto, you can see it's all the same. It's going to bolt in just like the original. I'm going to speed up again as I just tight those bolts in and then tighten them up with my socket, ratchet and extension. When you tighten them you want them nice and firm. They're not to be overly tight though. Put the extension back in and then plug your plug wire right back and then just repeat for the other seven.
We hope this helps you all. Brought to you by www.1AAuto.com. Your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that serve you on the internet and in person.
Tools used
Hose Pliers
Torque Wrench
8mm Wrench
Air Compressor
5/8 Inch Spark Plug Socket
Ratchet
All right, we wanna disconnect the battery, disconnect the negative cable. Use an 8-millimeter ratchet wrench or a wrench. And then slide that out of the way. We can take the spark plug wire off just on the spark plugs side. You might have to use some special pliers, like hose pliers, to get there boots off. Just like that. And just slide that to the side.
Now before you take the spark plug out, there could be some dirt and debris around the plug. Just take some compressed air and just spray right around the plug itself. And take a spark plug socket. This happens to be a 5/8 spark plug socket. And loosen the plug.
And slide the plug out. Take the new spark plug, put it in your spark plug socket and just carefully line it up. And you wanna torque this to 11 foot-pounds. And reconnect the spark plug wire, just line it up with the plug. Lock it down and then you can do the same procedure for the other ones.
Now we can hook up the battery. Line it up, get it started. And snug it up. Just make sure it's not loose. That's good.
Tools used
Hose Pliers
Torque Wrench
8mm Wrench
Air Compressor
5/8 Inch Spark Plug Socket
Ratchet
All right, we wanna disconnect the battery, disconnect the negative cable. Use an 8-millimeter ratchet wrench or a wrench. And then slide that out of the way. We can take the spark plug wire off just on the spark plugs side. You might have to use some special pliers, like hose pliers, to get there boots off. Just like that. And just slide that to the side.
Now before you take the spark plug out, there could be some dirt and debris around the plug. Just take some compressed air and just spray right around the plug itself. And take a spark plug socket. This happens to be a 5/8 spark plug socket. And loosen the plug.
And slide the plug out. Take the new spark plug, put it in your spark plug socket and just carefully line it up. And you wanna torque this to 11 foot-pounds. And reconnect the spark plug wire, just line it up with the plug. Lock it down and then you can do the same procedure for the other ones.
Now we can hook up the battery. Line it up, get it started. And snug it up. Just make sure it's not loose. That's good.
Tools used
10mm Socket
Ratchet
You can move these heater hoses out of the way. Just pull them out of the bracket and slide them to the side. Then you can access the coils.
You can take this wire off right here. Just twist it back and forth. You should be able to do it with your hand, and just slide it off like that. Disconnect the connector. There's a little tab. Just pull up on the tab, slide it out. Now just take a ten millimeter socket, take this bolt out here and the one right there. Get those bolts out. Grab the coil, just slide it up.
Take the new coil. Set it in position. Put the bolts in. Get those started. Right there and right there. Then I can torque these bolts to 71 inch-pounds. Plug in the coil. Lock it in place. Take the coil wire and slide it on. Then we're gonna do the same procedure for the rest of them.
And move these heater hoses, put them back in the bracket.
Tools used
7mm Socket
10mm Socket
Ratchet
Tools used
Flat Blade Screwdriver
7mm Socket
Ratchet
1. Removing the Ignition Coil
Disconnect the ignition coil wiring harness
Pry the spark plug wire off the ignition coil
Remove the two 7mm bolts from the ignition coil
Pull off the ignition coil
2. Installing the New Ignition Coil
Wipe down the ignition coil mounting area
Connect the ignition coil wiring harness
Line up the ignition coil with the bolt holes
Insert the two 7mm bolts into the ignition coil
Push the spark plug wire onto the ignition coil
Repeat these steps for the remaining ignition coils
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on this 2003 GMC Envoy XL, with the 5.3 liter V8 engine. The items that you'll need for this is a new ignition coil from 1AAuto.com, 7mm socket and ratchet, and a flat blade screwdriver.
Because this is a V8, there's four ignition coils on either side of the engine, four here, and four more here. Each one is held in with two 7mm bolts. Start off by disconnecting the harness. Just lift up on the tab and disconnect it, and then pull and pry off the spark plug wire from the ignition coil, and then remove those two 7mm bolts. Once the bolt's removed, the ignition coil will pull right off.
On the left, is the old ignition coil; on the right, is the new one from 1A Auto. You can see they're identical, and will fit exactly the same. Wipe down the area where the ignition coil goes. Reconnect the harness to your ignition coil to help hold it into place, and then line it up on the bolt holes, and replace those two 7mm bolts, and tighten them up. Reconnect the plug wire, and repeat for any of the other coils you want to replace.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
7mm Socket
10mm Socket
Ratchet
Pocket Screwdriver
Okay, friends. Before we get started on doing our ignition coil here, we just wanna make sure that you have safety is your number one concern. Always have your eye protection and your hand protection. Let's get started.
Let's come right over here on the passenger side of the engine. If we're looking for the coils, you're gonna see them right up along the top or side, right along here. All four going down the side and then, of course, on the other side of the engine you'll have the same four. Now, we're gonna show you on this front one right here, because it's the hardest one. And it's not very hard at all, but it is the hardest. We need to grab these heater core hoses, move them out of the way. Once they're out of the way we need to remove this bracket. Use your 10-millimeter and take off this nut.
The next thing we're gonna do is take a nice small pocket screwdriver, you can use pretty much anything, including your finger, but if you take the small pocket screwdriver, you can go right along here, lift up on this tab, and then you should be able to draw your electrical pigtail away.
Now let's move on down from the coil to the spark plug wire. Grab onto it. Give it a nice twist and pull it right off. Looking at the coil on either side, you're going to see a 7-millimeter bolt, remove both. Hold onto that coil, there's nothing holding it on there, except for this bolt at this point. There it is, friends.
Now it's gonna be time to install our brand new coil. Just gonna take it and bring it right down here, and I'm gonna line it up with exactly where I removed it from. Start in both of my bolts before I tighten either of them down. Go, both are straightened. Let's go ahead and snug them up. I always like to use a regular ratchet to make sure they're snug. Go ahead and connect in your electrical connector. Let's grab that spark plug wire. Go ahead and use a little bit of dielectric grease in there, that's gonna be helpful, and then connect it right onto your coil. Listen for a little click noise, give it a nice twist and a nice little tug, to make sure it's secured on there. You also wanna make sure that your spark plug wire is in no way touching that exhaust manifold.
So, now the replacement process for all the rest of the coils would be the same at this point. But moving along to finish up with this coil, we need to make sure we get this bracket back on. I'm gonna take the bracket, put it on there just like this. Snug it right up. There we are. Make sure it's nice and tight. Make sure you secure your heater core hoses. Double-check everything. This looks great.
Tools used
Socket Extensions
10mm Socket
Ratchet
1. Removing the Ignition Coil
Disconnect the ignition coil wiring harness
Remove the 10mm bolt from the hose bracket
Pull off the hose bracket
Disconnect the spark plug wire from the ignition coil
Remove the two 10mm bolts from the ignition coil
Pull the ignition coil up and out
2. Installing the New Ignition Coil
Push the new ignition coil into place
Insert the two 10mm bolts into the ignition coil
Connect the spark plug wire to the ignition coil
Push the hose bracket into place
Insert the 10mm bolt into the hose bracket
Connect the ignition coil wiring harness
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on this 2002 Chevy Suburban with the 5.3 liter, V8 engine. It's the same part and similar process on these Suburbans from 2000 to 2006. The items you'll need for this are a new ignition coil from 1AAuto.com and a 10mm socket and ratchet with an extension.
Your ignition coils are located right here. There are four on each side since this is a V8 engine. To remove these ignition coils, it's the same process for each of them; they're held in with two 10mm bolts. The only difference is this one right here that has a bracket for these hoses over it and that bracket also just held in with a 10mm bolt. We'll show you on this one since it's a slightly different procedure. Just lift up on the tab and disconnect that harness, and then, using a 10mm socket and ratchet, just remove that 10mm bolt, right there. Now you can just pull that bracket aside, and then, pull your spark plug wire from the ignition coil. Then remove the 10mm bolt at the top and the bottom of the coil. The coil will pull right off.
On the left, is the old ignition coil; on the right, is the new one from 1A Auto. You can see they're identical and they're going to fit exactly the same. Take your new ignition coil and push it down into place and then replace those two 10mm bolts. We'll fast forward as Don does this. Now reconnect your spark plug wire and then push this bracket back into place and replace that 10mm bolt. If you're replacing multiple ignition coils, obviousl,y you just repeat the process for each one and finally just reconnect the harness and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
ICA61751
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.