Part Details

  • Quantity: 6 Piece Set

Specifications:

  • Brand New Delphi Ignition Coil Kit
  • Comes as a Set of 6
  • Built to strict quality control standards
  • Direct replacements
  • 100% factory tested

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing Ignition Coils 2 and 4 (1:01)
    • Open the hood
    • Disconnect the ignition coil wiring harnesses
    • Remove the 10mm bolt from each ignition coil
    • Pull each ignition coil up and out
  2. step : Installing Ignition Coils 2 and 4 (Installing Ignition Coils 2 and 4)
    • Put the ignition coils into place
    • Connect the ignition coil wiring harnesses
    • Insert the 10mm bolt for each ignition coil
  3. step : Removing the Upper Intake Manifold (3:31)
    • Loosen the throttle body hose clamp with a flat blade screwdriver
    • Pull the coolant line out of the intake hose
    • Pull the intake hose off the throttle body
    • Remove the sensor from the intake hose
    • Disconnect the two hoses from the intake manifold
    • Disconnect the MAP sensor from the top of the intake manifold
    • Disconnect the two writing harness from the intake control valves at the front of the intake manifold
    • Disconnect the wiring harness from the throttle body
    • Remove the two 10mm nuts from the throttle body
    • Remove the seven 10mm bolts from the center of the intake manifold
    • Remove the two 10mm bolts from the manifold brackets
    • Remove the two 15mm bolts from the bottom of the throttle body bracket
    • Remove the bracket from the throttle body
    • Remove the two 15mm bolts from the manifold brackets
    • Pull off the intake manifold
    • Put paper towels into the intake manifold to keep out debris
  4. step : Removing the Remaining Ignition Coils (6:57)
    • Disconnect the ignition coil wiring harnesses
    • Remove the 10mm bolt from each ignition coil
    • Pull each ignition coil up and out
  5. step : Installing the Remaining Ignition Coils (7:18)
    • Put the ignition coils into place
    • Connect the ignition coil wiring harnesses
    • Insert the 10mm bolt for each ignition coil
  6. step : Installing the Upper Intake Manifold (7:38)
    • Remove the paper towels from the intake manifold
    • Clean the intake manifold surface with brake cleaner
    • Connect the PCV breather hose to the back of the valve cover
    • Remove the old gasket from the upper intake manifold with a pick
    • Press in the new intake manifold gasket
    • Remove the old EGR seal
    • Push on the new EGR seal
    • Put the upper intake manifold into place
    • Click the automatic transmission dipstick into place
    • Start the 10mm bolts for the manifold
    • Tighten the seven 10mm bolts in the center of the manifold to 9 foot-pounds, starting at the center
    • Connect the MAP sensor to the manifold
    • Connect the wiring harnesses for the two intake control valves
    • Put the manifold brackets into place
    • Insert the two 15mm bolts into the brackets
    • Insert the two 10mm bolts into the brackets
    • Connect the PCV hose to the manifold
    • Connect the two hoses to the manifold
    • Connect the throttle body wiring harness
    • Put the throttle body bracket into place
    • Start the two 10mm nuts onto the top of the throttle body bracket
    • Insert the two 15mm bolts into the bottom of the bracket
    • Tighten the two 10mm nuts onto the bracket
    • Push the intake hose onto the throttle body
    • Tighten the intake hose clamp with a flat blade screwdriver
    • Snap the coolant line into the intake hose bracket
    • Connect the MAP sensor to the intake hose
    • Push the intake hose onto intake tube if you disconnected them
    • Tighten the intake tube clamp with a flat blade screwdriver

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Gloves
  • Brake Parts Cleaner
  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Wrenches - Metric

  • Complete Metric Wrench Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2006-2010Chrysler 300 Chrysler 300 Ignition Coil 6 Piece Set V6 3.5L Delphi GN10310
2006-2010Chrysler 300 Chrysler 300 Ignition Coil 6 Piece Set V6 2.7L Delphi GN10310
2007-2008Chrysler Pacifica Chrysler Pacifica Ignition Coil 6 Piece Set V6 4.0L Delphi GN10310
2006-2010Chrysler Sebring Chrysler Sebring Ignition Coil 6 Piece Set V6 2.7L Delphi GN10310
2007-2010Chrysler Sebring Chrysler Sebring Ignition Coil 6 Piece Set V6 3.5L Delphi GN10310
2008-2010Chrysler Town & Country Chrysler Town & Country Ignition Coil 6 Piece Set V6 4.0L Delphi GN10310
2008-2010Dodge Avenger Dodge Avenger Ignition Coil 6 Piece Set V6 3.5L Delphi GN10310
2008-2010Dodge Avenger Dodge Avenger Ignition Coil 6 Piece Set V6 2.7L Delphi GN10310
2009-2010Dodge Challenger Dodge Challenger Ignition Coil 6 Piece Set V6 3.5L Delphi GN10310
2006-2010Dodge Charger Dodge Charger Ignition Coil 6 Piece Set V6 2.7L Delphi GN10310
2006-2010Dodge Charger Dodge Charger Ignition Coil 6 Piece Set V6 3.5L Delphi GN10310
2008-2010Dodge Grand Caravan Dodge Grand Caravan Ignition Coil 6 Piece Set V6 4.0L Delphi GN10310
2009-2010Dodge Journey Dodge Journey Ignition Coil 6 Piece Set V6 3.5L Delphi GN10310
2006-2008Dodge Magnum Dodge Magnum Ignition Coil 6 Piece Set V6 2.7L Delphi GN10310
2006-2008Dodge Magnum Dodge Magnum Ignition Coil 6 Piece Set V6 3.5L Delphi GN10310
2007-2011Dodge Nitro Dodge Nitro Ignition Coil 6 Piece Set V6 4.0L Delphi GN10310
2006Dodge Stratus Dodge Stratus Ignition Coil 6 Piece Set V6 2.7L Delphi GN10310

This part replaces:

  • Delphi GN10310
  • Hollander 610-00108
  • OE # 4606869AB
Only 2 left in stock
Part #: DEERK00071


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Delphi
Brand #: GN10310

How-to Video:

(13:32 min)