1ABPS02664-Hyundai Kia Rear Ceramic Brake Pads


Hyundai Kia Rear Ceramic Brake Pads TRQ

Guaranteed to fit: 2009 Hyundai Elantra

Part Details

  • Brake Pad Features & Benefits: OE Grade Multi-Layer Shim
  • Brake Pad Features & Benefits: Positive Mold Technology
  • Brake Pad Bonding Type: Premium Posi
  • Brake Pad Features & Benefits: Environmentally Compliant
  • Brake Pad Features & Benefits: Thermal Scorched
  • Brake Pad Friction Material: Ceramic
  • Kit Includes: Brake Pad Contact Point Grease
  • Kit Includes: Brake Pad Hardware

This part replaces:

  • TRQ BFA73210
Part 1ABPS02664
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Brand #: BFA73210

Frequently bought together

Vehicle Fit
Warranty & Shipping
How-To & Tools

Part Details

  • Brake Pad Bonding Type:   Premium Posi
  • Brake Pad Friction Material:   Ceramic
  • Kit Includes:
      Brake Pad Contact Point Grease
      Brake Pad Hardware
  • Brake Pad Features & Benefits:
      OE Grade Multi-Layer Shim
      Positive Mold Technology
      Environmentally Compliant
      Thermal Scorched

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (0:22)
    • Raise the vehicle with minimal weight on the tire
    • Loosen the five 21 mm lug nuts
    • Raise and support the vehicle
    • Remove the five lug nuts
    • Remove the hubcap
    • Remove the wheel
  2. step : Removing the Brake Caliper (0:54)
    • Remove the two 14 mm brake caliper slider bolts
    • Remove the brake caliper, prying it off if necessary
    • Set the caliper aside or hang it so there is no tension on the brake hose
    • Remove the 17 mm bolt and 17 mm nut securing the control arm to the knuckle
    • Move the control arm aside to give access to the second caliper bracket bolt
    • Remove the two 14 mm caliper bracket bolts
    • Remove the caliper bracket
    • Remove the brake pads from the caliper bracket, hammering them out from the back side if necessary
  3. step : Removing the Brake Rotor (7:16)
    • Remove the brake rotor screws
    • Remove the rotor
    • Hammer the rotor to break up rust if necessary
    • Loosen the brake shoes with the adjuster if necessary
    • Hammer the rotor out from behind if necessary
    • Pry the rotor out through the axle circle if necessary
    • Heat the adjuster to loosen it if necessary
    • Cut out the adjuster or brake shoe if necessary
  4. step : Installing the Brake Rotor (13:09)
    • Apply anti-seize grease to the wheel hub
    • Slide the brake rotor onto the wheel studs
    • Reinstall the rotor screw
    • Twist the rotor to check brake shoe contact
    • Turn the adjuster screw as necessary to adjust shoe contact
  5. step : Servicing the Brake Caliper (17:29)
    • Remove the caliper slider bolts to separate the caliper from the caliper bracket
    • Remove the two caliper sliders and apply brake grease
    • Reinstall the caliper sliders
    • Apply brake grease to the notches where the brake tins will sit
    • Install the brake tins into each notch of the caliper bracket
    • Apply brake grease to the ears and piston of the brake caliper
    • Install the brake pads into the caliper bracket
  6. step : Installing the Brake Caliper (20:37)
    • Install the caliper bracket onto the knuckle
    • Secure the caliper bracket with the two 14 mm caliper bracket bolts
    • Torque the two caliper bracket bolts to 43 ft-lb
    • Install the brake caliper onto the caliper bracket
    • Secure the caliper with the two 14 mm brake caliper slider bolts
    • Torque the caliper slider bolts to 23 ft-lb
    • Replace the control arm and secure it with the 17 mm bolt and 17 mm nut
    • Open the brake caliper bleeder screw to allow fluid to gravity bleed, then close the bleeder screw
  7. step : Installing the Wheel (26:25)
    • Slide the wheel onto the wheel studs
    • Replace the hubcap
    • Replace and tighten the 21 mm lug nuts by hand
    • Lower the vehicle with minimal weight on the wheel
    • Torque the lug nuts to 80 ft-lb in a star pattern
    • Lower the vehicle completely

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • Anti-Seize Grease
  • Brake Grease

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Impact Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 17mm Socket
  • 21mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 17mm Wrench

Fits the following Makes:

Year Make Model Description
2006-2009Hyundai Azera Hyundai Azera Rear Ceramic Brake Pads
2007-2008Hyundai Elantra Hyundai Elantra Rear Ceramic Brake Pads
2009Hyundai Elantra Hyundai Elantra SE Sedan Rear Ceramic Brake Pads
2009Hyundai Elantra Hyundai Elantra GLS Sedan Rear Ceramic Brake Pads
2010Hyundai Elantra Hyundai Elantra Sedan (Built Before 10/20/09 Production Date) Rear Ceramic Brake Pads
2001-2006Hyundai Santa Fe Hyundai Santa Fe Rear Ceramic Brake Pads
1999-2008Hyundai Sonata Hyundai Sonata Rear Ceramic Brake Pads
2005-2009Hyundai Tucson Hyundai Tucson Rear Ceramic Brake Pads
2001Hyundai XG300 Hyundai XG300 Rear Ceramic Brake Pads
2002-2005Hyundai XG350 Hyundai XG350 Rear Ceramic Brake Pads
2004-2006Kia Amanti Kia Amanti Rear Ceramic Brake Pads
2001-2010Kia Optima Kia Optima Rear Ceramic Brake Pads
2005-2010Kia Sportage Kia Sportage Rear Ceramic Brake Pads

Part Interchange

Brand Label Part Number
Raybestos EHT813H
Raybestos SGD813C
Raybestos MGD813CH
Raybestos Brakes MGD813CH
Raybestos Brakes EHT813H
Raybestos Brakes SGD813C

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Brand #: BFA73210
Product Reviews
5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Rear bresks
Great just what I was thinking I was getting!!!!!
February 2, 2020
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Customer service


Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

Hyundai is a registered trademark of Hyundai Motor Company. 1A Auto is not affiliated with or sponsored by Hyundai or Hyundai Motor Company. See all trademarks.

Hyundai Kia Rear Ceramic Brake Pads TRQ-1ABPS02664 does not fit your:

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a 2009 Hyundai Elantra with these options.