1ASBS00100-Honda Element Front Driver & Passenger Side Lower 2 Piece Ball Joint Set

Replaces

Honda Element Front Driver & Passenger Side Lower 2 Piece Ball Joint Set TRQ

1ASBS00100

Part Details

  • Set Quantity: 2 Piece

This part replaces:

  • Moog K500004
  • OE # 51210SCV000
  • OE # 51215SCVA00
  • TRQ PSA63085
FREE SAME DAY SHIPPING
Save 31%
List: $38.95 Save: $12.00
Part 1ASBS00100
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: PSA63085

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Part Details

  • Set Quantity:   2 Piece

Specifications:

  • Brand New Ball Joints
  • Comes as a Pair
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greasable versions.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (0:36)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Sway Bar Link (1:12)
    • Remove the lower sway bar link nut with a 14mm wrench and 5mm Allen bit
    • Pry the sway bar link to the side with a hammer and pry bar
  3. step : Removing the Lower Ball Joint (2:00)
    • Straighten out the cotter pin with needle nose pliers
    • Loosen the castle nut with a 17mm socket and breaker bar
    • Secure the rotor in place with a pry bar
    • Remove the axle nut with a 36mm socket and breaker bar
    • Press a pickle fork into place with a hammer to separate the ball joint
    • Tab out the end of the CV shaft with a hammer
    • Secure the axle shaft to the strut with a bungee cord
    • If the ball joint had a snap ring, remove it with snap ring pliers
    • Hammer the ball joint out of the spindle
    • Remove the ball joint
  4. step : Installing the Lower Ball Joint (6:23)
    • Insert the ball joint into the spindle with a ball joint press
    • Install the snap ring with snap ring pliers
    • Insert the CV axle into the spindle
    • Tighten the snap ring around the ball joint
    • Insert the CV axle into place
    • Tighten the castle nut
    • Torque the castle nut to 51 foot-pounds
    • Insert the cotter pin into place and bend an end down
    • Snip off the ends of the cotter pin
    • Torque the axle nut to 181 foot-pounds with a pry bar and torque wrench
  5. step : Installing the Sway Bar Link (10:02)
    • Pry up the sway bar into place
    • Tighten the lower sway bar link nut with a 14mm wrench and 15mm socket and ratchet
    • Torque the swar bar link nut to 29 foot-pounds
  6. step : Reattaching the Wheel (10:42)
    • Slide the wheel into place
    • Start the 19mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Hex Wrenches

  • 5mm Hex Wrench

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Snap Ring Pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 17mm Socket
  • 19mm Socket
  • 36mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Pickle Fork

  • Wrenches - Metric

  • 14mm Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
2003-2006Honda Element Honda Element Front Driver & Passenger Side Lower 2 Piece Ball Joint Set
2007-2011Honda Element Honda Element LX Front Driver & Passenger Side Lower 2 Piece Ball Joint Set
2007-2011Honda Element Honda Element EX Front Driver & Passenger Side Lower 2 Piece Ball Joint Set

Part Interchange

Brand Label Part Number
DIY Solutions SUS00508
DIY Solutions SUS00324
MOOG K500004
MOOG Chassis Products K500004

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: PSA63085
Product Reviews
5.00/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
2005 Honda element ball joints
I purchased my ball joints from 1aauto .com and they fit great I would refer my friends and family to buy Parts from use guys as well thank you very much
April 1, 2019
Lower ball joints
Lower ball joints worked well.
August 26, 2019
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Honda Element Front Driver & Passenger Side Lower 2 Piece Ball Joint Set TRQ-1ASBS00100 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.