Replaces

Honda Civic Steering & Suspension Kit Front - 1ASFK01868

These replacement suspension parts are just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • 14 Piece Suspension Kit includes:
    • (2) - FRONT Strut & Spring Assemblies - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Strut & Spring Assemblies - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT UPPER Control Arms - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT LOWER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT INNER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Sway Bar Links - LH (Driver Side) & RH (Passenger Side)
  • Parts are new, not remanufactured or refurbished
  • Direct replacements
  • Built to strict quality control standards

Worn ball joints can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace loose or worn ball joints with our quality replacement. One way to diagnose a loose, or warn ball joint, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint for play, if it is moving you probably need to replace it.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:40)
    • Loosen the lug nut covers
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Tie Rod (1:00)
    • Measure from the boot to the outer tie rod and record it
    • Loosen the 19mm nut on the tie rod with a 19mm wrench
    • Remove the cotter pin with pliers
    • Remove the castle nut with a 17mm socket
    • Hit the knuckle with a hammer
    • Twist the tie rod out
  3. step : Installing the New Tie Rod (2:13)
    • Twist on the new tie rod
    • Push the outer tie rod down into the knuckle
    • Replace the castle nut
    • Push the cotter pin into place and bend the ends in separate directions with pliers
    • Measure and double check the distance of the boot to the tie rod
    • Turn the tie rod joint with the 14mm wrench to adjust the distance
    • Replace and tighten the 19mm nut
  4. step : Reattaching the Wheel (3:15)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 19mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Suspension kit
Great Customer Service. Quality parts. Highly Recommended
February 23, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 4 answers
Does it come with new bolts and washers?
James A on Jan 23, 2018
BEST ANSWER: About 90% of these parts come with new bolts and washer. you will have to use some old bolts and washers as well.
Does this kit fit a set steering (rack and pinion) 97 CX?
Alfredo A on Feb 12, 2018
BEST ANSWER: Yes, according to the information you supplied, the part you’re looking at will be correct for your vehicle. If you have any other questions or would like to place an order with one of our customer service representatives, please feel free to give us a call.

Vehicle Fit

  • 1996-1998 Honda Civic Front Steering & Suspension Kit 14 Piece Set
  • 1999-2000 Honda Civic Front Steering & Suspension Kit 14 Piece Set (excluding SI Models)

This part replaces:

  • OE # 52338SL0003
  • OE # 52611S04G01
  • OE # 51605S01A01
  • OE # 51460S04023
  • OE # 51464S04013
  • OE # 53540S04013
  • OE # 53560S04013
  • OE # 53540S04003
  • OE # 51450S01023
  • Moog K9802
  • Moog K90123
  • Moog ES3332R
  • Moog ES3331R
  • Moog EV367
  • Moog K90451
  • Moog K90450
  • Dorman 520-669
  • Dorman 520-670
  • Hollander 527-59270L
  • Hollander 527-59270R
  • Hollander 511-58112L
  • Hollander 511-58112R
  • OE # 51460-S01-023
  • OE # 51450-S01-023
  • Monroe 181292
  • Monroe 181291L
  • Monroe 181291R
  • Monroe 171292
  • Monroe 171291L
  • Monroe 171291R
  • KYB SR4042
  • KYB SR4041
  • KYB SR4040
Part #: 1ASFK01868



How-to Video:

(03:54 min)