Replaces

Honda Civic FIT Vapor Canister Purge Valve - 1AEMX00210

This Vapor Canister Purge Valve is a new part. It mounts on the engine and is used to control the flow of vapors from the EVAPORATIVE system to the intake manifold. It is controlled by the vehicles main computer or ECM. When the ECM sends the activation signal, a plunger in the valve will move to seal the vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative loss system components. This valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative loss system is depressurized and allows "EVAP Control System (Small Leak)" diagnosis. If this valve is defective, the Check Engine Light will illuminate to Set with Small Leak Diagnosis. Some of the trouble codes associated with this part being defective are: P1456, P1448, P0449, and P0455.

Specifications:

  • Brand new component
  • Valve only, does NOT include canister
  • Replaces dealer part numbers: 36162-RNA-A01, 36162RNAA01
  • Engine mounted
  • Direct replacement
  • Built to strict quality control standards

Over time and daily use the valve can wear out causing the check engine light to set. If the valve is the problem, replace it now with this part.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Cowl Cover (0:23)
    • Open the hood
    • Prop the hood in the maintenance position
    • Pull the weather seal off the cowl cover
    • Remove the three plastic pins from the cowl cover with trim tools or needle nose pliers
    • Pop the cowl cover out of the cowl
    • Disconnect the windshield washer house coupler
  2. step : Removing the Cowl (2:44)
    • Apply rust penetrant to the 10mm bolt on each side of the cowl
    • Remove the 10mm bolt from front of each side of the cowl
    • Apply rust penetrant to the two 12mm bolts on each side of the cowl
    • Remove the two 12mm bolts on each side of the cowl
    • Apply rust penetrant to the 10mm bolt on the rear of each side of the cowl
    • Remove the 10mm bolt on the top of each side of the cowl
    • Apply rust penetrant to the 10mm bolt in the middle of the cowl
    • Remove the 10mm bolt in the middle of the cowl
    • Pull the cowl forward and out of the engine bay
  3. step : Removing the Vapor Canister Purge Valve Evap Solenoid (6:05)
    • Locate the valve near the rear atop of the throttle body
    • Loosen the hose clamp
    • Remove the hose from the valve
    • Disconnect the wiring harness
    • Remove the two 8mm bolts from the purge valve
    • Remove the purge valve
  4. step : Installing the Vapor Canister Purge Valve Evap Solenoid (7:43)
    • Place a tiny layer of white grease around the o-ring
    • Insert the purge valve into place
    • Tighten the 8mm bolts to the purge valve
    • Connect the wiring harness
    • Connect the hose to the purge valve
    • Tighten the hose clamp
  5. step : Installing the Cowl (9:05)
    • Put the cowl into place
    • Install the 10mm bolt on the front of each side of the cowl
    • Use masking tape to hold a 10mm bolt in your socket
    • Install the 10mm bolt in the middle of the cowl
    • Install the 10mm bolt at the rear of each side of the cowl
    • Insert the two 12mm bolts on each side of the cowl
  6. step : Installing the Cowl Cover (10:30)
    • Clean the bottom of the windshield with glass cleaner
    • Connect the windshield washer hose coupler
    • Put the cowl cover into place
    • Pop in the cowl cover clips
    • Push the three plastic pins into the cowl cover
    • Push the weather seal onto the cowl cover

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Gloves
  • Painter's Tape

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Sockets - Metric

  • 14mm Socket
  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2006-2010Honda Civic Honda Civic Vapor Canister Purge Valve L4 1.8L
2007-2008Honda FIT Honda FIT Vapor Canister Purge Valve

This part replaces:

  • OE # 36162RNAA01
  • Standard Motor Products CP641
  • Dorman 911-763
Only 1 left in stock
Part #: 1AEMX00210


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:07 min)