Replaces

Honda Civic Civic Del Sol CRX CV Axle Shaft TRQ CSA82134 - 1AACV00006

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Specifications

  • Brand new, not rebuilt
  • No core charge
  • Fits LH (Driver Side)
  • 36 1/4" Long
  • 26 Outer Splines
    • Not correct for models with 23 spline outer joint
  • 25 Inner Splines

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

Note: This is correct for models with or without ABS brakes.  The tone ring can be removed if the original CV axle did not have one and the vehicle did not originally come equipped with ABS brakes.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

    We recommend an alignment after completing this repair

  1. step : Removing the Wheel (0:50)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:27)
    • Remove the center cap from the wheel
    • Slide the wheel into place
    • Lower the vehicle to the ground
    • Have an assistant hold the brakes
    • Remove the 32mm nut with a large breaker bar
    • Secure the vehicle on jack stands
    • Pull off the wheel
    • Check to make sure the axle is free from the hub
  3. step : Removing the Caliper (2:03)
    • Remove the 12mm bolt from the brake hose
    • Remove the 10mm bolt from the sensor wire
    • Remove the 12mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Secure the caliper up in place with wire ties
  4. step : Removing the Axle (2:58)
    • Remove the 21mm pinch nuts and 19mm bolts
    • Pull the wheel knuckle out
    • Pry the axle out with a pry bar
    • Place a drain pan beneath the transmission
    • Pry the axle out of the transmission with a pry bar
  5. step : Installing the Axle (4:39)
    • Insert the axle into the transmission
    • Remove the new 32mm nut from the axle splines
    • Insert the axle into the wheel knuckle
    • Insert the 21mm pinch nuts and 19mm bolts into place
    • Hand tighten the 32mm hub nut
  6. step : Reinstalling the Caliper (6:10)
    • Place grease on your brake pads
    • Lower the caliper into place
    • Thread 12mm bolts by hand
    • Tighten bolts to 34 Newton Meters or 25 foot-pounds
    • Tighten the 10mm bolt to the sensor wire
    • Tighten the 12mm bolt to the brake hose
  7. After tightening, you might have to take the wheel off and dent the hub nut

  8. step : Reattaching the Wheel (7:39)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
    • Tighten the hub nut to 134 foot-pounds or 181 Newton Meters
    • Replace the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Drain Pan
  • Assistant
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 19mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 19mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1988-1991Honda CRX Honda CRX Front CV Axle Shaft Driver Side (excluding HF) TRQ CSA82134
1988-1991Honda Civic Honda Civic Front Wheel Drive Front CV Axle Shaft for Models with Automatic Transmission Driver Side TRQ CSA82134
1992-1998Honda Civic Honda Civic Front CV Axle Shaft Driver Side TRQ CSA82134
1999-2000Honda Civic Honda Civic Front CV Axle Shaft Driver Side (excluding SI Models) TRQ CSA82134
2001-2005Honda Civic Honda Civic Coupe Front CV Axle Shaft for Models with Automatic Transmission Driver Side TRQ CSA82134
2002-2005Honda Civic Honda Civic Sedan Front CV Axle Shaft for Models with Automatic Transmission Driver Side TRQ CSA82134
1993Honda Civic Del Sol Honda Civic Del Sol Front CV Axle Shaft Driver Side TRQ CSA82134
1994-1997Honda Civic Del Sol Honda Civic Del Sol Front CV Axle Shaft Driver Side (excluding VTEC) TRQ CSA82134
Part #: 1AACV00006


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: CSA82134

How-to Video:

(08:53 min)