Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Frequently bought together
Specify your vehicle's year, make and model to guarantee fit.
If your vehicle isn't listed, search Brake Kits
Part Details
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Going to take our 19 millimeter socket and breaker bar, and while the vehicle is on the ground, we'll loosen our lug nuts. Raise and support the vehicle. With the lug nuts loose, I can just take the socket and finish taking them off. Lug nuts loose, we'll take the wheel off and tire and put it aside.
Before you remove the caliper, you need to unbolt the rubber brake line from this bracket here so they have more space to move the caliper. I'm going to spray some rust penetrant on the backside of it and a little bit here. This is a 12 millimeter bolt—we use a socket and ratchet to remove it. Pull the bolt out, let the hose out of the bracket. Before you remove the lower and upper caliper slide bolts, make sure the e-brake is released because the parking brake or e-brake on this car works through the caliper. So if it's tight and pulled you're not going to be able to remove this caliper because it's going to be gripping the brake pads, the rotor, so just make sure that's released first. These are 12 millimeter bolts.
You may also need to counterhold the slide pins. These are 17 millimeter. I'm using a 12 millimeter box wrench to release these. That one I didn't need to counter hold the slide pin, it didn't turn. I'm going to leave that in there and then work on the top one. Remove the bolts. And I have a bungee cord ready. I'm going to hang this caliper up on the spring. May need a large flat bladed screwdriver or a small pry bar and just pump this caliper up and off. Take a bungee cord and hold that off to the side. Pop our old brake pads out of here with the pry bar and remove the lower and upper caliper bracket bolts. These are 14 millimeter—use a 14 millimeter box wrench. They can be on there pretty hard. I'm going to use a dead blow mallet to tap on the wrench to break it free. Work on the top one same way. Those loosen. I'm going to switch to a ratcheting wrench to make this a little quicker. The top bolt removed. Pull the caliper bracket off and put that aside.
Need to remove the retaining screws that are holding the brake rotor on. Spray a little rust penetrant in here. You need a big Phillips head screwdriver. The problem is when you go to turn it, it's going to want to turn the whole rotor. I'm going to throw a couple lug nuts on here. Take a pry bar and counterhold it and turn. I'm going to have someone help me and hold these with a long breaker bar and then, if you've got a decent screwdriver, you can actually put a wrench on here sometimes to give you a little extra leverage. Set up and try to turn this off. Push in and turn just like that. Let's try this one. If you wreck these taking them out I wouldn't worry about putting them back in.
All they do is hold the rotor against the hub when you've got the wheel off the car or whatever, it just keeps it from being loose, but you could use lug nuts to hold it in place while you reinstall the brake parts. I wouldn't worry about it. I'm going to take off these lug nuts I was using. The rotor is now loose. Careful not to drop it.
Here's the original brake pads from our vehicle and our brand new ones from 1AAuto.com. It has the same solid style brake rotor and same style pads. This would be the opposite side, but matching pads with the little pins that go into the piston and the wear indicators. Already come with shims installed. Same amount of lug holes and same holes for the mounting screws. These should fit on there and work great for us. Going to grab our caliper, unhook it from the bungee cord, just kind of move it over here. It’s still attached to the parking brake cable and the brake hose.
This piston can't be pushed in, it needs to be turned in. I'm going to use these needle nose pliers, there are tools for this but I'm going to use these pliers instead, and basically just turn it clockwise because when you pull the parking break it pushes the piston out, and part of that mechanism to retract this piston for our new brake pads, it needs to be turned in, so we're going to turn it clockwise. You don't want this boot to get twisted up that's around the cylinder in the brake caliper, so I'm just going to spray a little bit of rust penetrant. I'm going to take a bit and I'm very carefully just cleaning some of the rust from the edge, and hopefully what happens now is I can turn this piston clockwise and it won't twist the boot. Just using the pick to free it up and the oil to help it slide. I keep turning it. There we go, that's better. Alright.
So, once you get it turned down, just make sure that this is basically vertical. Maybe turn it just a little bit, because the inner pad has a pin on it that's going to sit in this slot. So, that looks pretty good like that. We're going to reuse our caliper bracket hardware. We need to clean it. These are just stainless steel. We’re just going to clean the dirt off. Spray some brake parts cleaner and use a wire brush. Repeat that for both sides. Now is a good time, while you have the caliper bracket off, to check that your slide pins are moving freely. That one feels good. That one also feels good.
If the clip pops off, don't worry about it, just get it cleaned up and clip it back into place. Take our new rotor. I'm going to put it on backwards first, take some break parts cleaner, clean off the oil that they come shipped in, wipe off any excess. I'll grab them by the edge, flip them over. I'm going to line up the counter sunk holes with those threaded holes there. I'm going to find them and line them up. If you've got these screws you can install them, if not, you can leave them off. You can just put a lug nut on here to hold it tight until you get the whole brake assembly back on. We'll put them back in. Just snug them down, they don't have to be super tight. All they do is keep the rotor from moving around when you're installing all the brake parts and taking the wheel and tire on and off.
Now we'll take brake parts cleaner and clean down the face of the rotor. Let's reinstall the bracket. Place it over the rotor, capture top bolts, might have to move the bracket around to get it to line up. That's threaded in. Capture the bottom one. I'm just going to switch to a ratcheting wrench so I can finish installing them and then I'll torque them afterwards. I'm going to torque the caliper bracket bolts to 54 foot-pounds. I'm just going to make sure the brake pad surface is clean. Just hit it with some brake parts cleaner. You don't want to have any grease or dirt on there. Take a little bit of break caliper grease, put it on the ears, and don’t have to go crazy with this stuff. This is going to be the inside pad, it has the wear indicator on it. It's going to sit in here just like this. Repeat that for the outer pad.
Take our bungee cord off, don't forget to take it out of here. Place the brake caliper back onto the bracket. You'll know pretty instantly if you didn't retract the piston far enough because the caliper won't want to go on. So that slid right on. I'm going to reinstall the bolts. Tighten this one up. Might get to a point where you're trying to tighten these caliper slide bolts, then they'll start to spin in the slides. The slides are 17 millimeter. You can use that to counter hold it. I'm just using a 12 millimeter socket and ratchet and I'm just going to tighten this up. The torque on these is 17 foot pounds—it's pretty light.
I'm just going to do it by hand. Just repeat that for the top one. This bleeder screw makes it a little tricky to get a box wrench in here but the socket and ratchet works perfectly. Don't forget, after you're done putting the brakes back together, put the bolt back in holding your rubber brake hose. Tighten that down. Alright. Put the wheel back on the car. You want the lugs caught, get them caught by hand first, we'll torque them with the vehicle weight on it when it's on the ground. Really just need to bring them down until they're seeded. The vehicle on the ground. The lug nut torque is 79.6 foot pounds, so we're going to do it 80. Do this in a cross pattern.
And the final step to push the caliper pistons back out to meet the pads. We're going to gently press in the brake and pump up the pedal pressure, and you'll feel it start to get harder.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Tools used
Tools used
Tools used
Tools used
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
I'm going to use the breaker bar and a 19-millimeter socket, and loosen the lug nuts with the vehicle on the ground. Raise and support the vehicle. We're using our two-post lift, but you can use a jack and jack stands. I'm going to use the socket and finish removing the lug nuts. The hubcap is held on with the lug nuts. Take the wheel and tire off. Put that aside.
Before I remove this caliper, I want to push the piston back in slightly so it's easier to pull off the pads. Use a large flat bladed screwdriver, and just kind of wedge it in here and gently pull it out. It will compress the piston in. It's just going to push that fluid back into the master cylinder. So we can also see that our caliper is moving nice and freely. The caliper's in good shape.
Now I can go ahead and remove these mounting bolts. Start with the bottom one. It's a 12-millimeter bolt. I'm using a closed-end wrench to loosen it. Spin it right out. Before I take it all the way out, I'll do the same to the top one. Thread both of these out. Hold on to the caliper so it doesn't fall. Pull the caliper right off the brake pads. Going to rest it right there for a second. Hold on to it.
I'll take a bungee cord, and I'll wrap a bungee cord around it. I'll just hook it up here to the spring. It will just keep it from getting in my way or falling on the floor. Hook that around so it holds it. Perfect. I'm going to pull these hardware springs right out and just kind of squeeze them together. They'll slide right out. They don't have much tension to them. Pull the brake pads out. Wiggle them out of the clips. Same for both of them. If they don't come out easily, you can take a flat bladed screwdriver, a large one, and just kind of push them out.
I'm going to use a large ratchet and a 17-millimeter socket to remove the upper and lower bracket bolts. Get them both broken free. Those are pretty loose. I'm going to hold on to the bracket, and just thread the bolts out by hand. I'm just going to hold the bracket because I don't want it to fall. Pull that out. The rotor is held to the hub with these two large Phillips head screws, so I'm going to use a large Phillips head screwdriver and loosen them. And these ones came out easily.
Sometimes they don't come out very easily. You have to rust penetrant. You might have to use an impact screwdriver. I got lucky on these ones, and they came out easily. The rotor should slide right off the hub. If it doesn't slide right off, there are threaded holes that you can put eight-millimeter by 1.25 bolts in here, and push the rotor off. But this is going to come right off.
Here's our original pads and rotors from our vehicle and our brand new pads and rotors from 1AAuto.com. They're an exact match: same style pad with the wear indicator. These have new shims on them. They are nice and thick. These weren't too bad, but we wanted to show you how to change them anyways. Same exact bolt pattern and vented rotor. These will fit great and work great in your vehicle.
I'm going to install the rotor backwards first. Take some brake parts cleaner. Just clean off the oil that it's shipped in so it doesn't flash rust. Wipe off the excess with a rag. This hub's in good shape. It's not overly rusty. I'm not going to worry about cleaning it. If it was really rusty, you could take a wire brush and knock off the heavy bits of rust, but this one's in good shape, so I'm going to leave it. Install the rotor into the correct side now.
Make sure you line up these screw holes with the threaded holes on the hub. I'm going to install the screws so it holds the rotor in place. And the torque on these is not very high. Just get them down hand-tight. All they do is hold the rotor in place while you're installing everything to keep it from flopping around. If you didn't have these or you destroyed them coming out, you could just put a lug nut on here to hold the rotor in place while you're working.
So I'll just get them a little snug. That's perfect just like that. Clean the fact of the rotor with some brake parts cleaner now, and just wipe off the excess. You can clean this hardware and reuse it. It's stainless steel. Just use some brake parts cleaner, wire brush, and clean it up. Do the same for the other side. Caliper slide pins I noticed earlier when I was moving the caliper in and out that they're moving nice and freely, so I'm not going to worry about them. They're in great shape.
This can be reinstalled in the vehicle. Put the caliper bracket in place. Get it roughly lined up. You might have to move it around a little bit. Thread the bolts in. The other bolt threaded in. I'll come back and torque these afterwards. The torque for these bolts was 79.6 foot-pounds. I'm going to do it to 80 foot-pounds. I'll just round up a little bit. Once it clicks, it's reached the torque and you're all set. Do the same for both. Just want to make sure the pad face is nice and clean—you didn't touch it with any greasy gloves or fingers. Just take some brake parts cleaner and just quickly spray it. You don't need to soak it. You just want to clean off any dirt that's on there or grease.
I'm going to take a little bit of brake caliper grease. I'll put it right on the ears. This is where they ride in the caliper hardware or clips. You don't want to put too much, just enough. These pads have a curve to them. The outer curve is going to match the outer curve of the rotor. Going to slide it into the clip in, and then slide it into the other clip. It will just sit up against the rotor like that.
Do the same for the outside pad. Going to reinstall our spring clips. They go on the little holes right here. They'll want to push the pads outwards. That's okay. These help the pads release after you let off the brake. Got to get them into place. That'll be okay for now. This piston is really—it's already compressed into the caliper, which is good. If it was sticking out further, it might not go on over the new pads because they're thicker. You could take your old brake pad, put it in here, and a large C-clamp, and just gently compress this in, but I can see that it's basically retracted into the caliper, so I'm going to try to install it as is. If I need to, I'll compress it some more.
So what's happening when you compress this piston, the brake fluid is being pushed back into the master cylinder. There's no need to open the cap or bleed the system. You may need to remove some extra fluid at the end because these pads will take up less fluid, and you can just remove it using a turkey baster. There's no need to open the bleeder screw on the caliper.
Install the caliper. Make sure it's not twisted around the line. Squeeze these together with one hand. Yep, that was compressed just enough. So these caliper slide pins have a flat spot. It's going to meet that flat spot there. Make sure both of them are set up that way, just like that.
Reinstall the slide pin bolts. Do that for both of them. Get them tight just with my fingers, and then I'll torque them. Torque these upper and lower slide pin bolts to 37 foot-pounds and a 12-millimeter socket. Once it clicks, it's all set. Do the same for both. Don't forget to take your bungee cord out.
Turn this all straight, and reinstall our wheel and tire. Lower the vehicle to the ground. Put the wheel and tire back on. Hubcap popped off. The lug nuts do go over the hubcap, so I'll just find the opening for the tire valve, and put it right over that. It should line up with the holes. It'll just snap in place.
Start our lug nuts by hand. One caught. Do the rest. The socket tighten these down. Torque these with the vehicle on the ground, but for right now just tighten them down by hand. Tighten them to 80 foot-pounds in a cross pattern.
Before you start your vehicle, just gently press on the brake pedal. It will bring those pistons out to meet the rotors, because we compressed them earlier. It'll slowly build up pressure. It starts getting harder. You don't have to get in here and slam it to the floor. Just gently pump it up. Got a nice hard pedal now. Your brake job is complete. You can go adjust the brake fluid level as necessary, but you're all set.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Brake Kits