1ASFU00226-Honda Accord Acura TSX Front Driver Side Upper Control Arm with Ball Joint


Honda Accord Acura TSX Front Driver Side Upper Control Arm with Ball Joint DIY Solutions


This part replaces:

  • Hollander 511-58199L
  • Dorman 520-931
  • Moog K620617
  • OE # 51460-SDA-A01
  • OE # 51460SDAA01
  • Moog RK620617
  • Mevotech CMS20404
  • DIY Solutions SUS05223
Save 17%
List: $62.95 Save: $11.00
Part 1ASFU00226
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: SUS05223
Vehicle Fit
Warranty & Shipping
How-To & Tools

This replacement front upper control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.


  • Fits LH (Driver Side) FRONT UPPER
  • Replaces dealer part numbers: 51460-SDA-A01, 51460SDAA01
  • Includes ball joint & bushings
  • Direct replacement
  • Built to strict quality control standards

Worn ball joints can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace loose or worn ball joints with our quality replacement.

One way to diagnose a loose, or warn ball joint, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint for play, if it is moving you probably need to replace it.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our control arms are designed to be direct replacements for the original factory parts.  They are 100% brand new and require no modifications for installation.  No special tools are required because all of the bushings come pre-installed.

Your DIY Solution—Complete Repair in One Purchase

Do you need an assortment of parts to complete a repair? Stop searching for parts individually and complete your repair in a single purchase with a customized kit or set from DIY Solutions.

High-Quality Parts From Trusted Brands

Parts in DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Guaranteed Fit

DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel ()
    • Partially raise the vehicle with the wheel still contacting the ground
    • Loosen the 19 mm lug nuts
    • Raise and support the vehicle on jack stands
    • Remove the lug nuts
    • Replace one lug nut loosely
    • Hammer the tire from the back side if the wheel is stuck
    • Remove the last lug nut and the wheel
  2. step : Removing the Strut ()
    • Remove the 14 mm lower strut bolt
    • Remove the 17 mm nut from the 17 mm wishbone bolt and remove the bolt
    • Remove the wishbone from the bottom of the strut
    • Remove the three 14 mm and two 12 mm nuts from the top strut mount
    • Remove the strut from the top mount
    • The strut will be fully removed in the next step
  3. step : Removing the Upper Control Arm (3:30)
    • Remove the upper control arm cotter pin
    • Remove the 17 mm upper control arm castle nut
    • Hit the upper knuckle to release the ball joint stud
    • Remove the 10 mm nut securing the ABS wire bracket to the upper control arm
    • Move the knuckle forward to remove the strut
    • Remove the two 14 mm inner upper control arm bolts
    • Remove the upper control arm
  4. step : Installing the Strut (6:02)
    • Insert the upper control arm bushings into place
    • Install the two inner 14 mm bolts
    • Using the provided guides on the body, raise the upper control arm to the loaded position
    • Torque the 14 mm bolts to 23 ft-lb
    • Insert the strut top mounting studs into position
    • Install the three 14 mm top mount nuts and the two 12 mm nuts
    • Torque the three 14 mm nuts to 37 ft-lb
    • Torque the two 12 mm nuts to 16 ft-lb
    • Insert the lower strut into the wishbone
    • Install the 14 mm lower strut bolt
    • Torque the 14 mm lower strut bolt to 32 ft-lb
    • Align the wishbone with the lower control arm
    • Install the 17 mm bolt and tighten the 17 mm nut onto it
    • Torque the 17 mm wishbone bolt to 47 ft-lb
  5. step : Installing the Lower Control Arm (11:47)
    • Remove the upper control arm ball joint cover
    • Insert the upper control arm ball joint into the knuckle
    • Install the ball joint castle nut
    • Torque the ball joint castle nut to 35 ft-lb
    • Continue tightening to align the castle nut with the cotter pin hole in the stud
    • Install the new cotter pin
    • Install the ABS wire bracket onto the upper control arm
    • Install the 10mm nut securing the bracket
  6. step : Installing the Wheel (14:25)
    • Slide the wheel onto the lug nuts
    • Replace the lug nuts and tighten them in a star pattern
    • Lower the vehicle with the wheel lightly touching the ground
    • Torque the lug nuts in a star pattern to 80 ft-lbs
    • Lower the vehicle completely

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 12mm Socket
  • 14mm Socket
  • 15mm Socket
  • 17mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 17mm Wrench

Fits the following Makes:

Year Make Model Description
2004-2008Acura TSX Acura TSX Front Driver Side Upper Control Arm with Ball Joint
2003-2007Honda Accord Honda Accord Front Driver Side Upper Control Arm with Ball Joint

Part Interchange

Brand Label Part Number
ACDelco 45D1162
Beck / Arnley 102-5290
Beck / Arnley 101-5290
Beck/Arnley 101-5290
Beck/Arnley 102-5290
Centric Parts 623.40016
DIY Solutions SUS05223
Delphi TC2250
Dorman 520-931
Dorman - OE Solutions 520-931
Dorman OE Solutions 520-931
Honda 51460SECA01
Honda 51460SDAA01
Honda 51460SDAA13
Honda 51460SDAA12
Honda 51460SDAA21
Honda OEM 51460SDAA12
Honda OEM 51460SDAA13
Honda OEM 51460SDAA21
Honda OEM 51460SECA01
Honda OEM 51460SDAA01
Ingalls Engineering CAK620617
MAS Industries CB59007
MAS Industries CB59037
MAS Industries CB59007PR
MAS Industries CB50077
MAS Industries CB59017
MOOG CK620617
MOOG K620617
MOOG RK620617
MOOG Chassis Products CK620617
MOOG Chassis Products K620617
MOOG Chassis Products RK620617
Mcquay-Norris FA4503
Mevotech GS20404
Mevotech MS20404
Mevotech CMS20404
NAPA 260-5189
NAPA 260-5607
NAPA Premium 2605607
Precision Driveline 3CB60067
Precision Driveline CB60067
Raybestos Chassis 502-1162
SYD 1509001

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

DIY Solutions
Brand #: SUS05223
Product Reviews
There are no reviews for this item.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Customer service


Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

Honda Accord Acura TSX Front Driver Side Upper Control Arm with Ball Joint DIY Solutions-1ASFU00226 does not fit your:

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.