1ASLF00003-Ford Mazda Mercury Front Driver Side Lower Control Arm with Ball Joint

Replaces

Ford Mazda Mercury Front Driver Side Lower Control Arm with Ball Joint

1ASLF00003

This part replaces:

  • Hollander 512-01380L
  • Dorman 520-223
  • Moog K620319
  • OE # 1F7034320
  • OE # 6L5Z 3079 BA
  • Moog CK620319
  • Moog RK620319
FREE SAME DAY SHIPPING
Save 27%
List: $143.95 Save: $39.00
Part 1ASLF00003
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: SUS05348

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

This replacement Front Lower Control Arm for your Mountaineer Explorer Ranger Mazda Pickup is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits LH (Driver Side) FRONT LOWER
  • Replaces dealer part numbers: 6L5Z-3079-BA, 6L5Z3079BA, F87Z-3050-BA, F87Z3050BA, F87Z-3069-AA, F87Z3069AA, 1F70-34-320, 1F7034320, ZZP1-34-550, ZZP134550, ZZP1-34-46X, ZZP13446X
  • Includes new ball joint and rear bushings
  • Control arm is new, not remanufactured or refurbished
  • Only fits vehicles that use a torsion bar suspension, does not fit vehicles that use a coil spring suspension

Worn ball joints or loose rear bushings can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace that heavily rusted, rotted, or damaged front lower control arm with the loose bushings or worn ball joints with our high quality all in one replacement.

One way to diagnose a loose, or warn ball joint on a control arm, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint and bushings for play, if it is moving you probably need to replace it.

Our control arms are designed to be direct replacements for the original factory parts.  They are 100% brand new and require no modifications for installation.  No special tools are required because all of the bushings come pre-installed.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (1:00)
    • Pry off the center cap with a flat blade screwdriver
    • Remove the wheel lock lug nut with a wheel lock key
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Torsion Key Cover (1:46)
    • Mark an index where the torsion bar enters the front lower control arm
    • Mark an index where the key meets the backside of the bar
    • Count the number of turns it takes to remove the middle 13mm tensioner bolt
    • Remove the four 13mm bolts from the key cover
  3. step : Removing the Torsion Key (3:37)
    • Set a two jaw puller into both side of the crossmember
    • Install the forcing screw into the divet on the torsion key
    • Add tension with a socket and breaker bar to move the key off of the keeper
    • Slide the keeper out of the crossmember
    • Loosen the two jaw puller to release tension from the key
    • Tap the key off of the end of the torsion bar with a hammer
  4. step : Removing the Torsion Bar (5:35)
    • Hit and release the torsion bar from the lower control arm with a hammer
    • Remove the torsion bar from the control arm
  5. step : Removing the Sway Bar Links (8:37)
    • Remove the lower bolt with a 16mm wrench and 18mm socket and ratchet
    • Loosen the bottom washers and bushings
    • Clip the bottom part of the link with pliers
    • Thread a nut on the bottom
    • Loosen the top bolt white hammer the sway bar up and out of the control arm
  6. step : Removing the Front Lower Control Arm (9:53)
    • Remove the two 13mm nuts on the bottom of the control arm
    • Straighten out the cotter pin with needle nose pliers
    • Remove the ball joint castle nut with a 24mm socket and ratchet
    • Tap the side of the control arm to tap the ball joint out, or use a pickle fork
    • Break the back control arm bolts loose with a 21mm socket and breaker bar
    • Remove the bolts with the captured nut in the frame if possible
    • Pull the control arm out of the frame
    • Remove the control arm
  7. step : Installing the Front Lower Control Arm (14:13)
    • Remove the new castle nut
    • Flip the control arm over
    • Insert the grease fitting into the ball joint
    • Tighten the grease fitting with an 8mm wrench
    • Insert the lower ball joint into the spindle
    • Start the castle nut on by hand
    • Apply brake grease to the face of the bushings, sleeve, and inside the sleeve
    • Apply brake grease inside the torsion bar slot
    • Install the control arm into the frame
    • Insert the back control arm bolts into place and tighten them preliminarily, not all the way
    • Tighten the 27mm ball joint nut
    • Torque the ball joint nut to 98 foot-pounds
    • Install the cotter pin and bend the ends
    • Line the shock into the control arm
    • Install the 10mm bolts and tighten them with a 10mm wrench and 13mm socket and ratchet
  8. step : Installing the Front Sway Bar Links (18:47)
    • Coat the bolt with anti-seize grease or lubricant
    • Insert a washer and bushing onto the bottom
    • Insert the bolt into the way bar
    • Insert a bushing and washer onto the bottom
    • Insert the sleeve onto the bar
    • Insert a washer and bushing onto the bottom
    • Insert the bolt into the control arm
    • Replace the bar for the other side
    • Insert a bushing and washer onto the bottom
    • Pry down on the sway bar to compress the bushings
    • Insert a 16mm socket and ratchet on top
    • Insert 18mm wrench on the bottom
    • Tighten the sway bar link to compress the bushings tightly
    • Tighten the other side
  9. step : Installing the Torsion Bar (19:54)
    • Insert the torsion bar into the control arm
  10. step : Installing the Torsion Key (20:14)
    • Insert the torsion key to the torsion bar
    • Set a two jaw puller into both side of the crossmember
    • Install the forcing screw into the divet on the torsion key
    • Add tension with a socket and breaker bar to move the key up
    • Insert the adjustor block into the crossmember and below the key
    • Loosen the tension to lower the torsion key onto the adjustor block
    • Remove the two jaw puller
  11. step : Reinstalling the Torsion Key Cover (21:12)
    • Reinstall the cover and the four 13mm bolts
    • Hand-tighten the adjusting bolt until it touches the bottom of the torsion key
    • Tighten the adjusting bolt back to the number of turns used to remove it
  12. step : Reattaching the Wheel (21:48)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds of torque in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Pick
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease
  • Safety Glasses
  • Gloves
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • 2 Jaw Gear Puller

  • Wrenches - Metric

  • 16mm Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
1995-2001Ford Explorer Ford Explorer Front Driver Side Lower Control Arm with Ball Joint
2001-2005Ford Explorer Sport Trac Ford Explorer Sport Trac Front Driver Side Lower Control Arm with Ball Joint
1998-2011Ford Ranger Ford Ranger 4 Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
2001-2005Ford Ranger Ford Ranger Edge Rear Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
2006-2009Ford Ranger Ford Ranger Sport Rear Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
1998-2001Mazda B2500 Truck Mazda B2500 Truck Rear Wheel Drive with Front Torsion Bar Suspension Front Driver Side Lower Control Arm with Ball Joint
1998-2007Mazda B3000 Truck Mazda B3000 Truck 4 Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
1999-2000Mazda B3000 Truck Mazda B3000 Truck Troy Lee Rear Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
2001-2007Mazda B3000 Truck Mazda B3000 Truck DS Rear Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
1998-2009Mazda B4000 Truck Mazda B4000 Truck 4 Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
1999-2000Mazda B4000 Truck Mazda B4000 Truck Troy Lee Rear Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
2001-2003Mazda B4000 Truck Mazda B4000 Truck DS Rear Wheel Drive Front Driver Side Lower Control Arm with Ball Joint
2004-2009Mazda B4000 Truck Mazda B4000 Truck Rear Wheel Drive with Front Torsion Bar Suspension Front Driver Side Lower Control Arm with Ball Joint
1997-2001Mercury Mountaineer Mercury Mountaineer Front Driver Side Lower Control Arm with Ball Joint

Part Interchange

Brand Label Part Number
ACDelco 45D3144
CARQUEST CA295B
Centric Parts 623.65033
Centric Parts 622.65035
DIY Solutions SUS05348
Dorman 520-223
Dorman - OE Solutions 520-223
Dorman OE Solutions 520-223
Falcon CA691
Falcon Steering Systems FCA690
Ford 6L5Z3079BA
Ford F77Z3079FA
Ford 7L5Z3079A
Ford F87Z3079EA
Ford 2L2Z3079BA
Ford YL2Z3079AA
Ford 1F7034320
Ford OEM F87Z3079EA
Ford OEM 6L5Z3079BA
Ford OEM 2L2Z3079BA
Ford OEM YL2Z3079AA
Ford OEM 7L5Z3079A
Ford OEM F77Z3079FA
Ingalls Engineering CAK620319
MAS Industries CB85153PR
MAS Industries CB85153
MOOG K620319
MOOG RK620319
MOOG CK620319
MOOG Chassis Products K620319
MOOG Chassis Products CK620319
MOOG Chassis Products RK620319
Mcquay-Norris FA4191
Mevotech GS20402
Mevotech CMS20402
Mevotech MS20402
Motorcraft MCSOE45
NAPA 260-5318
NAPA Premium 2605318
Precision Driveline CB40082
Raybestos Chassis 507-1144
SYD F77A3079FA

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
DIY Solutions
Brand #: SUS05348
Product Reviews
There are no reviews for this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Ford Mazda Mercury Front Driver Side Lower Control Arm with Ball Joint-1ASLF00003 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.