Kit Includes: (1) Pitman Arm (2) Front Outer Tie Rods (2) Front Sway Bar Links (1) Idler Arm (2) Front Inner Tie Rods
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Application Specific Design: No modifications necessary
Anti-Corrosion Coated: Enhanced surface life
Pre-greased: No additional maintenance required
Kitted for Restored Performance: Improved road-feel and handling
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How To Replace Front Stabilizer Bar Link 1997-2002 Ford Expedition
How to Replace Front Sway Bar Link 1997-2003 Ford F-150
How to Replace Outer Tie Rod 1997-2003 Ford F-150
How to Replace Pitman Arm 1997-2003 Ford F-150
How to Replace Inner Tie Rod 1997-2003 Ford F-150
How to Replace Idler Arm 1997-2003 Ford F-150
Created on:
Tools used
Hammer
14mm Socket
Rust Penetrant
Center Punch
Ratchet
9/16 Inch Socket
1. Removing the Stabilizer Links
Turn the wheels for access to the stabilizer link.
Spray the stabilizer with penetrating oil.
9/16� socket on the bottom and a 15mm socket on the top. Loosen the stabilizer link.
Use a hammer and punch to push the link out.
Use vice grips if needed.
2. Replacing the Stabilizer Link
Push the link up into place.
Put the link together in this order:
Bushing on the bottom of the control arm.
Bushing above the control arm.
Washer
Shaft
Washer
Bushing
Bushing
Washer
Nut.
Tighten the stabilizer to 15-17ft/lbs.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
In this video I'm going to show you how to replace the stabilize links on this 97 expedition, same as many Ford and Lincoln trucks and SUVs. When these go bad, sometimes they break out right and just kind of fall out and then your truck is going to sway back and forth more. Also you may here a clunking when you go over bumps and that clunking actually goes away when you're going over bumps but you're turning, because it's putting some pressure on the Lincoln and not making noise.
Tools you'll need, I put jack and jack stands on here but you can actually accomplish this with the vehicle on the ground. Obviously it's a lot easier to film it with jack and jack stands but you will need 9/16 and 14mm sockets. The 19mm socket will be if you're taking the lug nuts off. Ratchet and extensions. You'll need a hummer and a punch, vise-grip or locking pliers and penetrating oil. Actually those last four things are only if yours is rusted on there like ours was.
Okay, to film it, it's a lot easier to take the wheel off. This is a repair you can do just by turning if you want to replace the right hand one you can turn your wheels all the way to the right and you can probably get in there well enough, remove the stabilizer link without jacking up the vehicle or taking the wheel off. I'm going to loosen the lug nuts here then raise and secure the vehicle and remove the tire. Next I'm going to remove the stabilizer links. I'm going to spray the top of it with some penetrating oil and let it sit for a while. Okay this stabilizer links are sometimes difficult to get apart. You can use hand tools, they will come apart. I just chose to use a impact wrench just to make it easier. I have a 9/16 socket on the bottom and a 14mm socket on top.
Okay, use a hummer and pound down that bolt then use punch see if you can get it to go down through the sleeve, I end up actually having to use vise-grips and the wrench. Okay what I'm going to do here, I'm going to set up vise-grips on to this shaft, more tighter here. Here I'm going to install the sway bar link. I've already put a new link on the other side and just started the nut on it. The bushing always go towards the middle. We got bushing on the bottom going up to the control arm, bushing above that. My shaft goes on there and then the washer and the bushing. Okay push them down and in, and make sure that bushing is centered in there. Stabilizer bar. Now bushing and washer, and then my bolt or nut.
Okay, now you want to use the jack put pressure on the suspension and then tighten up the stabilizer to 15, to 17 foot pounds. You can put your tire back on and start each lug nut one by one make sure you don't cross-thread them. Tighten them down preliminarily. Put the lug nuts to 100 foot pounds using a star pattern.
We hope this helps you out. Brought to you by www.1AAuto.com your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
14mm Wrench
Air Chisel
14mm Socket
Ratchet
1/2 Inch Impact Gun
Tools used
21mm Socket
Adjustable Wrench
Side Cutters
Torque Wrench
Socket Extensions
Hammer
1/2 Inch Impact Gun
Tools used
21mm Socket
24mm Socket
32mm Socket
Torque Wrench
Brake Grease
Straight Cutters
10mm Socket
1/2 Inch Breaker Bar
3/8 Inch Breaker Bar
Tools used
21mm Socket
Adjustable Wrench
Side Cutters
Torque Wrench
Hammer
1/2 Inch Impact Gun
Tools used
21mm Socket
Metal Cutters
Torque Wrench
Hammer
Straight Cutters
10mm Socket
Liquid Thread Locker
PSA59072
In Stock
Product Reviews
Loading reviews
5.00/ 5.02
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
1A Auto is the only place!
Jama
March 13, 2019
I always check 1A for parts because of the fast service and the variety of needed parts.
Great products front end is new again
Robert
August 30, 2023
The parts fit very well, the function is absolutely perfect. Installation went great fit as expected. Will butyl more parts when the time comes for next needed items.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.