Replaces

Ford Focus Front Passenger Side CV Axle Shaft TRQ CSA82177 - 1AACV00120

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Specifications

  • Fits RH (Passenger Side) FRONT
  • Brand New
    • Not remanufactured
    • No core charge
  • Built to strict quality control standards
  • Correct for models with or without ABS

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:23)
    • Loosen the 19 mm lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Remove the wheel
    • You may replace one lug nut and pry the wheel from behind if it is difficult to remove
  2. step : Removing the Passenger Side Axle (1:28)
    • Remove the 32 mm axle nut
    • Rethread the axle nut loosely, then hammer the axle end to loosen it
    • Remove the axle nut
    • Remove the 15 mm lower ball joint nut from the T50 pinch bolt, and remove the bolt
    • Remove the 16 mm tie rod end nut and remove the tie rod end from the knuckle
    • Hammer on the lower control arm to loosen the ball joint from the knuckle
    • Push the axle out through the wheel hub while pulling the knuckle out away from the vehicle to remove the axle
    • Remove the two 13 mm carrier bearing bracket nuts, and remove the carrier bearing bracket
    • Hammer on the axle joint to remove the axle shaft from the transmission
    • Have a drain pan ready as transmission fluid will leak out when the axle is removed
  3. step : Installing the Passenger Side Axle (11:23)
    • Insert the axle shaft into the transmission
    • Hammer on the end of the axle until the shaft is seated properly in the transmission, and the carrier bearing is flush with the bracket mount
    • Reinstall the carrier bearing bracket with the two 13 mm nuts
    • Pull the knuckle out away from the vehicle and insert the axle into the wheel hub
    • Reinstall the lower ball joint with the sheild into the knuckle
    • Reinstall the T50 lower ball joint pinch bolt with the 15 mm nut
    • Torque the 15 mm nut to 37 ft-lb onto the T50 pinch bolt
    • Reinstall the tie rod end into the knuckle with the 16 mm nut
    • Torque the 16 mm tie rod nut to 35 ft-lb
    • Install the 32 mm axle nut
    • Torque the 32 mm axle nut to 233 ft-lb
  4. step : Installing the Wheel (20:01)
    • Slide the wheel onto the wheel studs
    • Install the 19 mm lug nuts by hand
    • Lower the vehicle with minimal weight on the wheel
    • Torque the 19 mm lug nuts to 93 ft-lb in a crossing pattern
    • Lower the vehicle completely

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease

  • Pliers, Cutters & misc Wrenches

  • Locking Pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket
  • 16mm Socket
  • 19mm Socket
  • 32mm Socket

  • Star Drivers & Sockets

  • T50 Socket

5.00/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
This is worth it
Older car not trying to dump a ton into it but this was good quality at a great price. Works perfectly. Fits exactly as advertised.
October 25, 2018
Easy Repair
Part is working great. Was an easy fix...once i got the old part off. Rusted axel nut was a pain but once we got it off the new part went in in less than 20 mins. Thanks again 1a Auto!
July 1, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does the middle bearing of this 1AACV00120 axle have to be pressed into the carrier?
Don G June 5, 2019
Written and video installation instructions are found on the product page under the "How-To & Tools" tab. If we do not have these you may be able to find them on Youtube or an automotive forum. We do not have any additional installation instructions.
Ian P June 6, 2019
Year Make Model Description
2000-2004Ford Focus Ford Focus L4 2.0L DOHC (Transmission ID MTX75) (8th Vin Digit 3) Manual Transmission Front Passenger Side CV Axle Shaft
2000-2011Ford Focus Ford Focus Automatic Transmission Front Passenger Side CV Axle Shaft
Part 1AACV00120
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: CSA82177