Replaces

Ford F150 Truck Wheel Bearing & Hub Assembly TRQ BHA53379 - 1ASHS00097

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Tapered Roller Bearing

These replacement hub & bearing assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Comes as a PAIR
    • Fits LH (Driver Side) or RH (Passenger Side) FRONT
  • 3 Bolt Flanges
  • Fit 5 Lug Wheels
  • Replaces dealer part numbers: F65Z1104BA, F65Z-1104BA, F75W1104EA, F75W-1104EA, XL341104BB, XL34-1104BB, XL341104BD, XL34-1104BD, XL3Z1104BC, XL3Z-1104BC
  • Studs already installed (Studs are M12's (12mm))
  • Fits only F150 4x4, (w/12mm wheel bolts & rear wheel ABS) exc. 7700 GVW
  • Direct replacements
  • Built to strict quality control standards
  • Fit 4WD (Four Wheel Drive) Models only
  • Fit models with RWAL (Rear Wheel Anti-Lock Brakes) only

What are Tapered Bearings and Why Use Them?

Tapered bearings are better than roller ball bearings at handling forces exerted on the bearing during cornering (known as axial load) in trucks and large cars. 

Roller ball bearings have spherical ball bearings between two straight rings (called races). Tapered bearings use tapered rollers shaped like flat-topped cones and two races angled from the outside to the inside of the bearing. The greater the angle, the more axial load the bearing can handle.

Your model came from the factory with tapered bearings. This type of bearing handles cornering forces better for trucks and large cars. Roller ball bearings work well for smaller cars, but replacing a tapered bearing with a roller ball bearing will result in increased wear and faster failure.

 

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA53952 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (0:30)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:00)
    • Straighten the cotter pin on the nut with needle nose pliers
    • Remove the cotter pin
    • Thread three or four lug nuts on
    • Hold the rotor still with a pry bar
    • Loosen the 35mm hub nut
  3. step : Removing the Brake Caliper (2:48)
    • Use a c-clamp to push in the pistons
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Lift the caliper up and off to the side
    • Secure the caliper with a bungee cord
    • Remove the rotor
  4. step : Removing the Wheel Hub (5:02)
    • Remove the three 15mm bolts from the hub
    • Tap the wheel hub off with a hammer
    • If the axle end won't move, place a block of wood on the end and tap it in with a hammer
  5. step : Installing the Wheel Hub (9:38)
    • Apply grease to the axle shaft splines
    • Slide the wheel hub onto the axle shaft splines
    • Tighten the 15mm bolts
    • Torque the bolts to 110-148 foot-pounds
    • Reinstall the axle nut
    • Torque the axle nut to 188-254 foot-pounds
    • Slide in the cotter pin to the nut
    • Bend the cotter pin
  6. step : Installing the New Brake Pads (13:12)
    • Put the rotor on
    • Put the caliper on
    • Thread the 18mm bolts by hand
    • Tighten bolts to 136 foot-pounds
    • Clean the rotor with brake parts cleaner or mineral spirits
  7. step : Reattaching the Wheel (14:14)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 83-112 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 35mm Socket
  • 15mm Socket
  • 18mm Socket
  • 19mm Socket

4.5 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
0
0
0
No problems
These wheel bearing hub assembly's fit and worked great on my 1997 F150.
October 20, 2017
Purchased
1 year ago
Great buy give it four star due to no wheel hub bolts, had to purchased them from the Ford dealership. They installed easy and save a lot of money. I would recommended others to buy this item.
March 15, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1997-1999Ford F150 Truck Ford F150 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Pair TRQ
2000Ford F150 Truck Ford F150 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 12mm Stud Size & Rear Wheel ABS Brakes Pair TRQ

This part replaces:

  • TRQ BHA53379
Part #: 1ASHS00097


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA53379

How-to Video:

(15:08 min)