Replaces

Ford F150 Lincoln Mark LT Front Cross Drilled & Slotted Zinc Coated Performance Brake Rotor Pair

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A

Part Details

  • Wheel Lug Count:   6 Lug
  • Brake Rotor Type:   Cross Drilled & Slotted
  • Quantity:   Pair
  • Front Brake Rotor Diameter:   12.99 in. (330mm)
  • Brake Rotor Coating:   Zinc Coated
  • Front Brake Rotor Venting Type:   Vented
  • Product Line:   Performance

Specifications:

  • Comes as a matched Pair
  • Includes LH (Driver Side) & RH (Passenger Side) Front
  • Cross drilled, Slotted, And Zinc Coated
  • Direct replacement
  • Fits 6 Stud Wheels
  • Vented
  • 12.99" (330mm) diameter
True Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:44)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:21)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Check for gouges on both sides of the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
  3. step : Removing the Brake Pads (2:09)
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove the two 13mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  4. step : Removing the Brake Rotor (3:02)
    • Remove two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
    • If the rotor will not come off, thread one lug nut and tap the rotor loose with a hammer
  5. step : Installing the Brake Rotor (3:31)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Apply grease to the caliper slides
    • Remove the brake pad slides
    • Clean the slide mounting area with a wire brush
    • Put the bracket back into place
    • Start the two 18mm bolts by hand
    • Tighten the 18mm bolts to 95 foot-pounds of torque
  6. step : Installing the Brake Pads (5:39)
    • Put the brake pad slides into place
    • Push the brake pad slide tabs into place with a hammer and flat blade screwdriver
    • Apply grease to the brake pad tabs
    • Install the new brake pads into the bracket
    • Push in the brake pad clips
    • Put the caliper on
    • Thread the two 13mm bolts by hand
    • Tighten bolts to 25 foot-pounds
  7. step : Reattaching the Wheel (8:42)
    • Remove the placeholder lug nut
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut to X foot-pounds
    • Tighten the lug nuts to 110 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  8. step : Testing the Brakes (9:31)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Wire Brush
  • Jack Stands
  • Large C-Clamp
  • Floor Jack
  • Hammer

  • Materials, Fluids, and Supplies

  • White Grease

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 21mm Socket
  • 13mm Socket

4.67/ 5.0
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
1
0
0
0
Exact part needed for my repair.
I purchased these rotors to replace the warped rotors on my F-150. The replacement was as easy as the video stated and took about 1 hour per side. The parts perform just as I had hoped.
October 19, 2018
Brake rotors
I would recommend this product because it was a perfect match, very easily installed and came super quick. No complaints other than the lugs were not pressed in completely but that was east to work around.
September 24, 2019
Great value
I needed to replace the wheel bearing but decided to take the easy route and swap out the assembly, plus this upgraded the rotors as well. The old rotors were in fine shape but braking still improved with these.
November 10, 2019
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does this comes with wheel bearing inside rotor?
Joseph D June 23, 2019
Yes but you need to put bearing grease on the bearings
Donald D June 23, 2019
Thank you for contacting us. Though this rotor does include the lug nuts, the bearing itself will not be pressed into this kit.
Andrew P June 24, 2019
Do these come with hub bearing inside the rotor?
Joseph D June 23, 2019
This will not include the hub bearing inside the rotor.
Emma F June 23, 2019
Yes.
Andra M June 23, 2019
Yes
J O September 24, 2019

Fits the following Makes:

Year Make Model Description
2004Ford F150 Truck Ford F150 Truck New Body Style Rear Wheel Drive with 6 Lug Wheels Front Cross Drilled & Slotted Zinc Coated Performance Brake Rotor Pair 12.99 in. (330mm)
2005-2008Ford F150 Truck Ford F150 Truck Rear Wheel Drive with 6 Lug Wheels Front Cross Drilled & Slotted Zinc Coated Performance Brake Rotor Pair 12.99 in. (330mm)
2006-2008Lincoln Mark LT Lincoln Mark LT Rear Wheel Drive Front Cross Drilled & Slotted Zinc Coated Performance Brake Rotor Pair 12.99 in. (330mm)

Part Interchange

Brand Label Part Number
Aimco 54107
Bendix PRT5519
DuraGo BR54107
Raybestos Brakes 680178
Wagner BD126116

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Only 7 left in stock
Part 1APBR00322
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.