1ASFK02487-Ford Explorer Mercury Mountaineer Suspension Kit 6 Piece Set

Replaces

2004 Mercury Mountaineer Suspension Kit 6 Piece Set

1ASFK02487-1017486-2004
Guaranteed to fit: 2004 Mercury Mountaineer

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Front Upper Ball Joints
  • Quantity: 6 Piece Set

This part replaces:

  • Moog K8694T, K80771
  • Moog K7275
  • Moog K80008
  • OE # 1L2Z3084AA
  • OE # 1L2Z3085AA
FREE SAME DAY SHIPPING
Save 38%
List: $72.95 Save: $28.00
Part 1ASFK02487
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: PSA56308

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools

Part Details

  • Quantity:   6 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Sway Bar Links
      (2) Front Upper Ball Joints

Specifications:

  • Brand new Suspension Kit
  • Comes as a 6 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller


Fits the following Makes:

Year Make Model Description
2002-2003Ford Explorer Ford Explorer 4 Door Suspension Kit 6 Piece Set
2004-2005Ford Explorer Ford Explorer Suspension Kit 6 Piece Set
2002-2005Mercury Mountaineer Mercury Mountaineer Suspension Kit 6 Piece Set

Part Interchange

Brand Label Part Number
DIY Solutions SUS00100
DIY Solutions SUS00153
DIY Solutions SUS06607
MOOG K80771
MOOG K8694
MOOG K7275
MOOG K8695T
MOOG K80008
MOOG Chassis Products K8694
MOOG Chassis Products K8695T
MOOG Chassis Products K80008
MOOG Chassis Products K7275
MOOG Chassis Products K80771

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: PSA56308
Product Reviews
5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Life-savers
These parts came in fast and whent on easy when we got the proper tools. Thats allways the key thing about Auto mechanics they have to have a lot of tools thats why they charge so much! Thanks for the parts 1A-Auto
July 17, 2017
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

Mercury is a registered trademark of Ford Motor Company. 1A Auto is not affiliated with or sponsored by Mercury or Ford Motor Company. See all trademarks.

Ford Explorer Mercury Mountaineer Suspension Kit 6 Piece Set TRQ PSA56308-1ASFK02487 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a 2004 Mercury Mountaineer with these options.