Replaces

Ford Escape Mercury Mariner Window Regulator Pair - 1AWRK00449

Part Details

  • Regulator Option: with Motor
  • Quantity: Pair
  • Operation: Power

Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT DOORS
  • Includes the power window motors
  • Replaces dealer part numbers: 2L8Z7823201BA, 2L8Z 7823201 BA, 2L8Z7823200BA, 2L8Z 7823200 BA
  • Power operation
  • Direct replacements
  • Built to strict quality control standards

 

Please Note: These window regulators are high quality aftermarket parts that meets or exceeds the performance of the original. They have been subjected to extensive testing and quality control standards. That is why we offer these regulators with our superior warranty!

Installation

  • This repair is easier than you may think. You'll find our installation videos helpful. In our experience removing and replacing the door panel is the most involved step in the repair. On most vehicles this only requires removing a few screws and push-in clips.
  • You'll get a great feeling of accomplishment after you complete this repair knowing you saved money, and you didn't have to give up your car for a day at the repair shop. Your passengers and other drivers will be amazed.

Fit guaranteed

  • 1A Auto will refund you with no hassle if this window regulator does not fit the application stated.
  • This regulator will install just as your original does. Save time and money.

Quality

  • Be confident this part will work right. Every regulator is tested after assembly to make sure all mechanisms are working correctly.
  • It is important that your new regulator works for a long period of time. The design of this regulator is tested to withstand 10,000 cycles. That is enough to raise and lower your window 3 times per day for 9 years.

Value

  • Windows that don't work can be frustrating. They can also hurt your vehicles value. An inoperable window could mean $200-$500 discounted off a dealer trade value or asking price.
  • Some shops and dealers charge more for parts and repairs when they think you don't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly repair bill.

Item Condition: New

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:44)
    • Pry off the trim piece inside the door handle with a flat blade screwdriver
    • Remove the two Phillips screws at the bottom of the door panel
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw inside the door pull
    • Remove the door handle bezel
    • Lift the door panel up and off
    • Remove the wiring harness from the switch panel
    • Remove the Phillips screw from the bracket on the door
    • Carefully peel off the water shield
  2. step : Removing the Window Regulator (2:40)
    • Loosen the two 10mm bolts that hold the window to the regulator
    • Raise the window by hand
    • Pull the window out back first
    • Disconnect the window motor lead
    • Remove the three 10mm bolts from the motor
    • Remove the two 10mm nuts from the regulator
    • Pinch the tab and remove clip on the wiring harness
    • Pull the window regulator out through the door
  3. step : Installing the New Window Regulator (5:05)
    • Remove the three nuts from the new motor
    • Push the regulator into the door
    • Thread the three 10mm nuts into the motor
    • Reconnect the window motor lead
    • Place the two nuts on the regulator rails and tighten them
    • Lower the window, place the front into the track, then the rear
    • Slide the window onto the clips in the regulator
    • Tighten the two 10mm bolts that hold the window to the regulator
    • Test the regulator by connect the window switch wiring to the switch panel
  4. step : Reinstalling the Door Panel (8:37)
    • Put the water shield into place
    • Connect the wiring harness to the switch panel
    • Push in the door panel clips
    • Connect the door handle bezel
    • Tighten the Phillips head screw inside the door pull (larger screw)
    • Tighten the Phillips head screw inside the door handle (natural color)
    • Tighten the two Phillips screws at the bottom of the door panel (Skinnier in back, larger in front)
    • Attach the trim piece inside the door handle

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2001-2007Ford Escape Ford Escape Front Power Window Regulator with Motor Pair
2005-2007Mercury Mariner Mercury Mariner Front Power Window Regulator with Motor Pair

This part replaces:

  • Dorman 741-604, 741-605
Part #: 1AWRK00449


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:14 min)