Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This replacement fog light is just what you need to get your vehicle in good looking form again!

Specifications:

  • RH (Passenger Side)
  • Bumper Mounted
  • Replaces dealer part numbers: 81210-06070, 81210-0D040, 8121006070, 812100D040
  • Injection molded plastic
  • DOT (Department of Transportation) & SAE (Society of Automotive Engineers) approved
  • Direct replacement fog light
  • Fog light does not include bulbs or wiring

This fog driving lamp is a great replacement and has good cost savings over a fog light from the dealer.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Front Bumper (0:24)
    • Place tape along the edge of the bumper to mark its location
    • Remove the 10mm bolts from the splash shield
    • Remove the splash shields
    • Turn the clip in the fender liner on either side
    • Pull back the fender liner
    • Remove the 10mm bolt from the bumper on either side
    • Remove the 10mm bolt from the metal support on top of the bumper
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Remove the Phillips retainer from the bracket
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Pull the bumper off of the bracket
  2. step : Removing the Headlight (6:19)
    • Remove the 10mm bolts from the headlight bracket
    • Pull the headlight out
    • Disconnect the headlight wiring harness
  3. step : Servicing the Bulbs (9:38)
    • Twist the bulb socket counterclockwise out of the light
    • Pull the bulb off of the socket
    • Push on the new bulb
    • Twist the bulb clockwise into the light
  4. step : Installing the New Headlight (11:10)
    • Reconnect the wiring harness to the headlight
    • Line up the bolt holes on the headlight bracket to the bolt holes on the vehicle
    • Replace the 10mm bolts and grommets into the headlight bracket
  5. step : Installing the Front Bumper (13:08)
    • Hang the bumper on the top brackets
    • Push the bumper into the bracket on both sides
    • Press in the push clips to the headlights
    • Tighten the Phillips retainers to the metal bracket
    • Press in the clips to the bumper
    • Tighten the screw to the bumper behind the fender liner on both sides
    • Replace the splash shield
    • Tighten the 10mm bolts to the splash shield

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Painter's Tape

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

5.00/ 5.0
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
0
Great value
Perfect fit, looks as if it might be OEM unit, easy to install, simple straightforward swap. Longer to lift car, remove rubber shield, reach unit. Then ten minutes to remove and swap replacement.
February 3, 2017
Just Perfect
Perfect fit. The replacement from 1A Auto looks better than the original light. The hardest part about changing it out with the old one was getting into the wheel well.
February 9, 2017
Fog light installation for 2009 Venza
The part was exactly the right fit and performs well. The video on taking the front bumper panels off was also extremely helpful for the installation process. Very happy with the project and result..
September 17, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2013Lexus GS350 Lexus GS350 Fog / Driving Light Passenger Side
2013Lexus GS450h Lexus GS450h Fog / Driving Light Passenger Side
2010-2012Lexus HS250h Lexus HS250h Fog / Driving Light Passenger Side
2008-2013Lexus IS-F Lexus IS-F Fog / Driving Light Passenger Side
2008-2011Lexus LX570 Lexus LX570 Fog / Driving Light Passenger Side
2013Lexus LX570 Lexus LX570 Fog / Driving Light Passenger Side
2010-2013Lexus RX350 Lexus RX350 Fog / Driving Light Passenger Side
2010-2013Lexus RX450h Lexus RX450h Fog / Driving Light Passenger Side
2006Scion xA Scion xA Fog / Driving Light Passenger Side
2008-2010Toyota Avalon Toyota Avalon Fog / Driving Light Passenger Side
2007-2014Toyota Camry Toyota Camry Fog / Driving Light Passenger Side
2009-2013Toyota Corolla Toyota Corolla Fog / Driving Light Passenger Side
2008-2010Toyota Highlander Toyota Highlander Fog / Driving Light Passenger Side
2009-2013Toyota Matrix Toyota Matrix Fog / Driving Light Passenger Side
2010-2011Toyota Prius Toyota Prius Fog / Driving Light Passenger Side
2006-2012Toyota Rav4 Toyota Rav4 Fog / Driving Light Passenger Side
2007-2008Toyota Solara Toyota Solara Fog / Driving Light Passenger Side
2009-2016Toyota Venza Toyota Venza Fog / Driving Light Passenger Side
2007-2016Toyota Yaris Toyota Yaris Fog / Driving Light Passenger Side
Part #: 1ALFL00309


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(17:26 min)