This replacement Ford Ranger Pickup Truck door handle pair is just what you need to get your Ford in good looking form again!

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Injected molded plastic with black textured finish
  • Direct replacement for original handle

These parts are direct bolt on parts and built to strict quality control standards. They are a great replacement and have substantial cost savings over dealer units.

Part Details

  • Quantity: Pair
  • Color: Black

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the door handle (1:07)
    • Use a Flat blade screwdriver to pry apart the crank handle and remove the T20 screw to remove the crank handle.
    • Remove the two Phillips screws in the door pull and unclip the door pull.
    • With your Phillips screwdriver, remove the screw down by the bottom of the door panel.
    • Pull the door panel off and gently peel back the water shield.
  2. step : Remove the outside door handle (2:42)
    • Unclip the door latch rod from the door handle.
    • On the outside of the door, lift the handle to expose to rivets.
    • Use a hammer and punch to punch out the rivets.
    • Take your drill and 1/4 in bit to drill out the rivets.
    • Remove the debris with your flat blade screwdriver.
    • Take your old broken outside door panel out.
  3. step : Install the new outside door handle. (4:30)
    • Transfer the top lock rod from the old handle to the new one.
    • Use two bolts and two lock nuts to install the new handle in lieu of the rivets you drilled out earlier.
    • Tighten them down with a socket and ratchet.
    • Clip the door latch rod back into place.
  4. step : Install the door panel (8:47)
    • Clip the door panel back on.
    • Secure with the two Phillips screws.
    • Replace the door pull and tighten down the Phillips screws.
    • Re-install the window crank with the T20 Torx screw.
    • Clip down the top of the window crank handle.

Tools needed for replacement:

    Drills, Drill Bits & Related

  • Drill

  • Materials, Fluids, and Supplies

  • Coarse Threaded Bolts (to replace rivets)

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
Excellent value
Normally you would pay more than this for just one at your local auto parts store.(and you have to drive there) No problems on install,exact replacement and I have one for the other door if it goes.
July 12, 2018
Purchased
3 weeks ago
Would recommend these door handlesd
Installation was straight forward and had no problems with the install. My old handles had a broken spring somewhere and didn't return to their closed and locked position. Required some drilling but installation video was very helpful. They work great.
December 6, 2017
Purchased
over 2 years ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1993-1997 Ford Ranger Black Exterior Door Handle Pair
  • 1998-2000 Ford Ranger XL Black Exterior Door Handle Pair
  • 1994-1997 Mazda B2300 Truck Black Exterior Door Handle Pair
  • 1998-2000 Mazda B2500 Truck Black Exterior Door Handle Pair
  • 1994-2000 Mazda B3000 Truck Black Exterior Door Handle Pair
  • 1994-2000 Mazda B4000 Truck Black Exterior Door Handle Pair

This part replaces:

  • OE # F37Z1022405A
  • OE # F37Z1022404A
Part #: 1ADHS00082

How-to Video:

(10:47 min)