1AECI00200-Dodge VW Chrysler Ignition Coil

Replaces

2009 Dodge Nitro V6 4.0L Ignition Coil

1AECI00200-526409-2009
Guaranteed to fit: 2009 Dodge Nitro

Fit Details

  • Engine Displacement (Metric): V6 4.0L

Part Details

This part replaces:

  • Hollander 610-00108
  • Standard Motor Products UF-502
  • OE # 4606869AB
  • OE # 4606869AA
  • Beck Arnley 178-8517
  • Borg Warner E1003
  • Standard Motor Products UF503
  • Wells C1918
  • Delphi GN10311
  • Walker Products Inc. 921-2092
  • Wells C1720
  • Standard Motor Products UF502
  • Wells C2116
  • Delphi GN10310
  • Beck Arnley 178-8518
  • Borg Warner E1002
  • Wells C1522
  • Walker Products Inc. 921-2093
  • TRQ ICA61796
FREE SAME DAY SHIPPING
Save 30%
List: $39.95 Save: $12.00
Only 3 left in stock
Part 1AECI00200
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: ICA61796

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools

The ignition coil is a crucial part of your ignition system. It's function is to convert the 12 volt power of your vehicle's electrical system in to 35,000 or more volts. This produces a high intensity spark at the spark plug which then ignites the fuel in the cylinder. Coils in general will wear out over time and cause a misfire condition. In engines like this that use a coil, if the coil goes bad, the complete assembly needs to be replaced.

This Ignition Coil features the following specifications:

  • New not remanufactured
  • Replaces dealer part number: 4606869AA, 4606869AB, 4606869 AA, 4606869 AB
  • Built to strict quality control standards
  • Direct replacement
  • 100% factory tested

 

This is an electrical part and is tested before it leaves our manufacturer.

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Direct Fit Replacement

Guaranteed to fit and function properly for your specific application.

Optimum Performance

Meets or exceeds requirements of the vehicle. Provides the correct primary and secondary resistance, voltage output, and spark energy needed to restore original operating condition.

Premium Quality

Manufactured with quality materials to meet highest quality control standards in the industry.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing Ignition Coils 2 and 4 (1:01)
    • Open the hood
    • Disconnect the ignition coil wiring harnesses
    • Remove the 10mm bolt from each ignition coil
    • Pull each ignition coil up and out
  2. step : Installing Ignition Coils 2 and 4 (Installing Ignition Coils 2 and 4)
    • Put the ignition coils into place
    • Connect the ignition coil wiring harnesses
    • Insert the 10mm bolt for each ignition coil
  3. step : Removing the Upper Intake Manifold (3:31)
    • Loosen the throttle body hose clamp with a flat blade screwdriver
    • Pull the coolant line out of the intake hose
    • Pull the intake hose off the throttle body
    • Remove the sensor from the intake hose
    • Disconnect the two hoses from the intake manifold
    • Disconnect the MAP sensor from the top of the intake manifold
    • Disconnect the two writing harness from the intake control valves at the front of the intake manifold
    • Disconnect the wiring harness from the throttle body
    • Remove the two 10mm nuts from the throttle body
    • Remove the seven 10mm bolts from the center of the intake manifold
    • Remove the two 10mm bolts from the manifold brackets
    • Remove the two 15mm bolts from the bottom of the throttle body bracket
    • Remove the bracket from the throttle body
    • Remove the two 15mm bolts from the manifold brackets
    • Pull off the intake manifold
    • Put paper towels into the intake manifold to keep out debris
  4. step : Removing the Remaining Ignition Coils (6:57)
    • Disconnect the ignition coil wiring harnesses
    • Remove the 10mm bolt from each ignition coil
    • Pull each ignition coil up and out
  5. step : Installing the Remaining Ignition Coils (7:18)
    • Put the ignition coils into place
    • Connect the ignition coil wiring harnesses
    • Insert the 10mm bolt for each ignition coil
  6. step : Installing the Upper Intake Manifold (7:38)
    • Remove the paper towels from the intake manifold
    • Clean the intake manifold surface with brake cleaner
    • Connect the PCV breather hose to the back of the valve cover
    • Remove the old gasket from the upper intake manifold with a pick
    • Press in the new intake manifold gasket
    • Remove the old EGR seal
    • Push on the new EGR seal
    • Put the upper intake manifold into place
    • Click the automatic transmission dipstick into place
    • Start the 10mm bolts for the manifold
    • Tighten the seven 10mm bolts in the center of the manifold to 9 foot-pounds, starting at the center
    • Connect the MAP sensor to the manifold
    • Connect the wiring harnesses for the two intake control valves
    • Put the manifold brackets into place
    • Insert the two 15mm bolts into the brackets
    • Insert the two 10mm bolts into the brackets
    • Connect the PCV hose to the manifold
    • Connect the two hoses to the manifold
    • Connect the throttle body wiring harness
    • Put the throttle body bracket into place
    • Start the two 10mm nuts onto the top of the throttle body bracket
    • Insert the two 15mm bolts into the bottom of the bracket
    • Tighten the two 10mm nuts onto the bracket
    • Push the intake hose onto the throttle body
    • Tighten the intake hose clamp with a flat blade screwdriver
    • Snap the coolant line into the intake hose bracket
    • Connect the MAP sensor to the intake hose
    • Push the intake hose onto intake tube if you disconnected them
    • Tighten the intake tube clamp with a flat blade screwdriver

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Gloves
  • Brake Parts Cleaner
  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Wrenches - Metric

  • Complete Metric Wrench Set


Fits the following Makes:

Year Make Model Description
2006-2010Chrysler 300 Chrysler 300 V6 3.5L Ignition Coil
2006-2010Chrysler 300 Chrysler 300 V6 2.7L Ignition Coil
2007-2008Chrysler Pacifica Chrysler Pacifica V6 4.0L Ignition Coil
2006-2010Chrysler Sebring Chrysler Sebring V6 2.7L Ignition Coil
2007-2010Chrysler Sebring Chrysler Sebring V6 3.5L Ignition Coil
2008-2010Chrysler Town & Country Chrysler Town & Country V6 4.0L Ignition Coil
2008-2010Dodge Avenger Dodge Avenger V6 3.5L Ignition Coil
2008-2010Dodge Avenger Dodge Avenger V6 2.7L Ignition Coil
2009-2010Dodge Challenger Dodge Challenger V6 3.5L Ignition Coil
2006-2010Dodge Charger Dodge Charger V6 2.7L Ignition Coil
2006-2010Dodge Charger Dodge Charger V6 3.5L Ignition Coil
2008-2010Dodge Grand Caravan Dodge Grand Caravan V6 4.0L Ignition Coil
2009-2010Dodge Journey Dodge Journey V6 3.5L Ignition Coil
2006-2008Dodge Magnum Dodge Magnum V6 2.7L Ignition Coil
2006-2008Dodge Magnum Dodge Magnum V6 3.5L Ignition Coil
2007-2011Dodge Nitro Dodge Nitro V6 4.0L Ignition Coil
2006Dodge Stratus Dodge Stratus L4 2.7L Ignition Coil
2009-2010Volkswagen Routan VW Routan V6 4.0L Ignition Coil

Part Interchange

Brand Label Part Number
Airtex 5C1565
BWD E1002
Beck / Arnley 178-8517
Beck/Arnley 178-8517
Borg Warner E1002
BorgWarner E1002
CARQUEST 52-1827
Chrysler 4606869AD
Chrysler 4606869AC
Chrysler 4606869AB
Chrysler 4606869AA
DENSO Auto Parts 673-5302
Delphi GN10310
Denso 673-5302
Echlin IC582
NAPA Mileage Plus IC582SB
Original Engine Management 50096
Richporter C-739
Spectra Premium C-739
Spectra Premium C-754
Spectra Premium Industries C-754
Spectra Premium Industries C-739
Standard Motor Products UF-502T
Standard Motor Products UF-502
Volkswagen 7B0905715D
WPS World Power Systems CUF502
Walker Products 921-2092
Wells C1720
Wells C1522

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: ICA61796
Product Reviews
4.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
1
0
0
0
Review for my part ordered
My order was delivered quick and was in good condition. The part works amazing as well. Over all I am a satisfied customer.
January 8, 2019
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

Dodge is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Dodge or FCA US LLC. See all trademarks.

Dodge VW Chrysler Ignition Coil TRQ-1AECI00200 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a 2009 Dodge Nitro with these options.