Replaces
Frequently bought together
Part Details
Left Hand Drive:
All of our auto parts are intended for Left Hand Drive USDM vehicles. If your vehicle is Right Hand Drive, please ensure the part is correct for your specific vehicle.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the blower motor fan assembly, as well as the blower motor resistor in this Dodge Ram. This one's a 2008, but the procedure is the same for 2002 to 2008. You'll need a new blower motor and resistor kit from 1AAuto.com, a Phillips screwdriver, as well as an 8mm socket with a ratchet and extension.
Your blower motor resistor is located under the dashboard on the passenger side, just below the glove box. We'll disconnect the electrical connector, and remove these two #2 Phillips head screws. Remove the resistor from the bottom of the HVAC box.
Disconnect the electrical connector, and remove the three 8 millimeter bolts. There's one in the back here that you're not going to be able to see. We're going to use an 8 millimeter socket ratchet and extension. Remove the blower motor from the HVAC box.
Here we have our old part that we removed from the vehicle, and our new part from 1A Auto. As you can see, they're identical. We have this ceramic heat-sink on the top of the resistor here, the same 4-pin connection at the bottom, as well as the same two bolt holes.
Here we have our old part that we removed from our vehicle, and our new part from 1AAuto.com. As you can see, we have the exact same size fan cage here, as well as the same base and mounting locations, the same motor, and the same 2-pin connector on the bottom.
Install your new blower motor into the HVAC box. Reinstall the three bolts, tighten the bolts up with your 8 millimeter socket ratchet and extension, and reconnect the electrical connector.
Install the new blower motor resistor into the bottom of the HVAC box, and start your two Phillips head screws. Tighten them down with your #2 Phillips head screwdriver. Reconnect your electrical connector.
Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
All right, friends. To get started on our blower motor resistor, you wanna be underneath the passenger-side dash. Grab onto your wire, and right along here, you're gonna find a tab. Go ahead and squeeze that. Pull this down. Give it a nice look. Make sure you don't see any funny colors. This looks great, so we'll set it aside. You're gonna find two mounting bolts on this. There's one right there and one on the far side towards the front. Remove them both. Grab the resistor. Pull it right out of here. Here it is, friends.
All right, friends. Now, it's gonna be time to install our brand new resistor. Something that I want you to pay attention to is this area right here where it's kind of beveled. That's gonna be facing towards the front of the vehicle. And take it, and slide it right on up and in here. Perfect. Now, we'll just start in both of our bolts, and then we'll snug them up. Go ahead and connect in your connector. There it is. All right. Now, you just need to test it.
Tools used
All right, friends. To get started on our blower motor, we're gonna come right underneath the passenger side of the dash along this kick panel, and you're gonna find some wiring. Go ahead and squeeze on the tab for your connector, give it a little wiggle, and pull this right down. Take a peek, make sure you don't see any funny colors. This looks great, let's set it aside. On your blower motor, you're gonna see three mounting bolts. You're gonna need a Torx head bit to get these out, so go ahead and grab that, remove all three bolts, and then we'll remove the blower motor. All right. Let's go ahead and pull this out. There it is, friends.
All right. Now, it's gonna be time to get our brand new blower motor in here. Something that I want you to pay attention to is this area right here. If you look at it, you can see it sticks out much further than the other mounting holes. With that said, put this facing towards the driver side, and now we'll get this right up and in here. Good, that's situated perfectly. Start in all three of your bolts and then snug them up. That looks great. Let's connect in our wiring here. Push it in, listen for a click, give it a nice tug. Now all you need to do is test it out.
