Replaces

Dodge Mirror - 1AMRE01829

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Mirror Operation:   Power
  • Mirror Color / Finish:   Textured Black
  • Mirror Heating Type:   Heated

Specifications:

  • Fits LH (Driver Side)
  • Power operation
  • Heated glass
  • Folding - Manual operation
  • Sail mount design - Mounts in the corner of the door
  • Injection molded black textured plastic housing
  • Direct replacement
  • Built to strict quality control standards

Special Note:

  • Unless otherwise noted, replacement mirrors will only work properly on vehicles with the exact same options. If your vehicle does not have the options listed in specifications, the mirror(s) may not function properly.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (1:06)
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw at the front top corner of the door panel
    • Remove the two Phillips head screws on the bottom of the door panel
    • Lift the door panel up and off
    • Pop the lock bezel out
    • Pry up the window switch panel by hand
    • Disconnect the window switch wiring harnesses
    • Remove the four Phillips screws from the speaker
    • Pry off the speaker
    • Disconnect the speaker wiring lead
  2. step : Removing the Side Mirror (2:34)
    • Disconnect the mirror wiring harness
    • Remove the three 10mm nuts from the mirror
    • Have an assistant hold the mirror
    • Push in the clips on either side of the harness connection
    • Remove the mirror
  3. step : Removing the Protective Rubber Boot (3:18)
    • Pry up the door soleplate with a flat blade screwdriver
    • Pull the glove box down
    • Push in the tabs on either side of the glove box
    • Pull the glove box down and remove it from the hinge
    • Push in on the tabs on the body harness
    • Pry out and remove the body harness
    • Disconnect the wiring harness
    • Push the rubber boot through the door to release the harness
    • Carefully peel the top left corner of the water shield
  4. step : Removing the Dash Panel (4:58)
    • Remove the side dash panel by hand
    • Remove the screw from the pillar trim with a 4mm Allen wrench
    • Remove the pillar trim
    • Disconnect the dome harness
    • Remove the two Phillips screws from the lower dash panel
    • Pull out on the lower dash panel
  5. step : Installing the Power Fold and Light Wiring Harness (5:51)
    • Run one of the power fold harnesses behind the center and across to the passenger side
    • Feed the wire up through the dash and through the hole on the body
    • Repeat the process for the light harness for the passenger side
    • Move back 18 inches on the wire
    • Cut a foot of the insulation off toward the body of the car
    • Pull the rubber body off the body harness
    • Pull the harnesses out with a flat blade screwdriver
    • Feed the folding and light harness through the body harness boot
    • Place the wires on the corner of the harness connection
    • Slide the harness back into the body
  6. step : Installing the Mirror Wiring Harnesses (8:14)
    • Feed a straightened out coat hanger or stiff wire through the boot
    • Pull the wires through the boot
    • Tape the wires to the coat hanger or wire with electrical tape
    • Feed the wires and coat hanger carefully back through the boot
    • Feed the wires into the door and out through the top hole without interfering with the window regulator
    • Feed the wires through the door and into the mirror pad
    • Hook the wire harnesses into the mirrors
  7. step : Installing the Folding Tow Mirror (10:17)
    • Put the mirror into place
    • Insert and the three 10mm nuts to the mirror
    • Tighten the 10mm nuts
    • Remove the end of the all black wire
    • Loosen the 10mm bolt below the mirror
    • Wrap the ground wire around the bolt
    • Tighten the 10mm bolt
  8. step : Installing the Protective Rubber Boot (11:01)
    • Pull the rubber boot into place and back through the door
    • Reconnect the harnesses
    • Pull the wires through on the other side
    • Snap in the body harness
    • Wire-tie the light and folding wires to prevent movement
    • Push on the water shield
  9. step : Installing the Mirror Wiring Harnesses (11:41)
    • Sustain the harnesses together on the passenger side with electrical tape
    • Wire-tie the harnesses up into the lower panel to prevent them from hanging
    • Wiretap the power fold harness to a switched power source
    • Probe the orange line with an electrical connector
    • Hook the puddle light wiretaps to the blue and green striped wire that ran the dome lights
    • Connect the dome light harness
    • Test the puddle lights
    • Push in the pillar trim
    • Tighten the screw with a 4mm Allen wrench
    • Ground the fold switch to a screw at the bottom of the dash
  10. step : Installing the Mirror Switch (13:30)
    • Drill out a hole in a small panel with a dremel to fit the mirror switch
    • After running the harnesses through both doors connect the switch to the wiring harness
    • Turn the vehicle on
    • Test the power folding switch
    • Turn the vehicle off
    • Disconnect the wiring harness in the engine compartment to create more room
    • Place a piece of stiff wire up through the harness boot
    • Hook the stiff wire onto the power source wire
    • Pull the wire back into the vehicle
    • Open the fuse box
    • Remove the parking light fuse
    • Hook the power source fuse to the parking light fuse
    • Push in the parking light fuse
    • Push the fuse box cover down
    • Reconnect the wiring harness
    • Hook the driver side marker light to the power wire ran from the fuse box with a wiretap
    • Turn the vehicle on
    • Test the marker light
    • Turn the vehicle off
    • Wire-tie the excess wires up into place underneath the dash panel
  11. step : Installing the Lower Dash Panel (16:35)
    • Push the lower dash panel into place
    • Insert and install the lower Phillips head screws
    • Connect the power mirror switch harness
    • Press the power mirror switch into the dash panel
    • Push in the side panel
    • Push in the door soleplate
    • Push in the glovebox
  12. step : Installing the Door Panel (17:18)
    • Reconnect the mirror harness
    • Put the speaker into place
    • Insert the four Phillips screws into the speaker
    • Connect the speaker wiring lead
    • Lift the door panel into place
    • Push in the door panel clips
    • Push in the lock bezel
    • Insert and tighten the two Phillips head screws on the bottom of the door panel
    • Insert and tighten the Phillips head screw at the front top corner of the door panel
    • Insert and tighten the Phillips head screw inside the door handle

Tools needed for replacement:

    Drills, Drill Bits & Related

  • Drill

  • General Tools

  • Assistant

  • Hex Wrenches

  • 4mm Allen Wrench

  • Materials, Fluids, and Supplies

  • Coat Hanger
  • Wire Ties
  • Electrical Tape

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

3.60/ 5.0
5 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
1
1
0
1
Great Product Great Price
I discovered A1 Auto on YouTube with their "How to" video. It was very detailed and was spot on with the instructions. I changed out my mirror in 15 minutes. I couldnt believe what I saw on the video was exactly what I encountered. Next time I have to work on my truck Im checking out this place first.
January 24, 2017
Great price, poor quality.
When I saw the price for this replacement mirror, I was shocked. $60?... Wow! Installation was fairly easy, and the product looks like the OEM part. The only thing I dont like about the mirror is that it "shakes" while driving. The swivel base is not a tight fit, so the mirror is not as stable as should be.
January 26, 2017
Not happy
The mirror did NOT get delivered to my house very upset over this
October 21, 2017
Great product
Received my mirror quickly,it was of great quality and after watching the installation video,I had the mirror installed in 20 minuets..
January 18, 2018
Side mirror
The product was a great fit and everything works as it should, the only dislike is that the glass vibrates and shakes at highway speeds
May 13, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
am i going to have a problem with this mirror ratteling?
Kevin L September 1, 2015
I just bought one for my 2009 Dodge 2500. Perfect fit and the plug for the electric was exactly the same. It was a no brainer to do and im not a mechanic. No Worries!
Joel N September 1, 2015
Not at all, If installed correctly it fits like a glove. Havent had any problems with it. (Had it for about a year now)
Christopher K September 1, 2015
Year Make Model Description
2005-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Power Heated Textured Black Mirror Driver Side
2005-2009Dodge Ram 2500 Truck Dodge Ram 2500 Truck Power Heated Textured Black Mirror Driver Side
2005-2009Dodge Ram 3500 Truck Dodge Ram 3500 Truck Power Heated Textured Black Mirror Driver Side
Part #: 1AMRE01829


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(18:55 min)