Replaces

Dodge Dakota Durango CV Axle Shaft Pair TRQ CSA82479 - 1AACS00031

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   Pair

Specifications

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT OUTER
  • Approximate Dimensions:
    • Length: 20-13/16"
    • Inboard Spline Count: 29
    • Outboard Spline Count: 31
  • Built to strict quality control standards

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

Note: You may need to reuse your original inner stub shaft with this new replacement CV axle.  The splined shaft on the inner joint from your original assembly can be removed and installed onto the new CV assembly.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the wheel and remove the brakes. (1:00)
    • Loosen your lug nuts
    • Raise and secure the car.
    • Remove the lug nuts and wheel.
    • Unbolt the caliper and secure it up with a wire tie
    • Remove the rotor and set aside.
  2. step : Remove the axle (2:10)
    • Remove the cotter pin
    • Put the wheel back on and lower the car.
    • Use a 32 mm socket and breaker bar to remove the hub nut.
    • Raise and secure the car again and remove the wheel.
    • Give the axle a good rap with a hammer to loosen it.
    • Remove the bolts mounting the axle.
    • Pull out the axle.

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • A Piece of Pipe (for leverage)
  • 1/2 Inch Breaker Bar
  • Torque Wrench

  • Sockets - Metric

  • 19mm Socket
  • 14mm Socket
  • 32mm Socket

5.00/ 5.0
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
0
cv Joint and hubs.
Great parts. The problem. They show how to remove and replace each. I’ve been trying to gage axle off the hubby for 3 days. I’ve tried heating them and now I just beat the crap out of them. I hope I don’t need a new knuckle and lower ball joint. Your help maybe?
October 6, 2017
Excellent all the way around
Excellent product, looks and feels better than the original and fits exactly like the original at a much lower cost. Shipping cost was low and shipping time was extremely fast. I would definitely recommend this to any one needing to replace theirs.
November 26, 2017
Great part, fast shipping
I ordered CV joints. They were easy to install, and appeared much higher quality than the parts store I went to go check out. I just had to wait a little longer. Great price too! I will be ordering more parts soon.
May 15, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
I am having problems with the c clamp on reinstallion. Is there different depths for the groove in which the c clamp sets?
Maurice M February 22, 2018
Hi Maurice, If you are talking about the c-clip in the shaft end that goes to the inside then no, there are not different depths. As long as the shaft diameter and length match your old one and the c-clip and groove are in the same place as you old one it should pop right in. I use a hard grease (wheel bearing grease) around the c-clip and on the shaft splines then just wiggle it around while pushing it in. You should hear the c-clip click in and then be unable to pull the cv-axle back out
R E February 22, 2018
Look at your old cv shaft. If the groove with the c clip on your old cv shaft isnt the same as it is on your new cv shaft, youve got the wrong one.
Justin F March 3, 2018
Year Make Model Description
2001Dodge Dakota Dodge Dakota Front Outer CV Axle Shaft Pair (Built After 9/11/00 Production Date) TRQ CSA82479
2002-2004Dodge Dakota Dodge Dakota Front Outer CV Axle Shaft Pair TRQ CSA82479
2001Dodge Durango Dodge Durango Front Outer CV Axle Shaft Pair (Built After 9/11/00 Production Date) TRQ CSA82479
2002-2003Dodge Durango Dodge Durango Front Outer CV Axle Shaft Pair TRQ CSA82479
Part #: 1AACS00031


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: CSA82479

How-to Video:

(09:34 min)