1ADSH00052-Dodge Chrysler Rear Driveshaft Coupler

Replaces

Dodge Chrysler Rear Driveshaft Coupler Dorman 935-301

1ADSH00052

Part Details

This part replaces:

  • Dorman 935-301
  • OE # 5166337AA
  • OE # 5166338AA
  • OE # 5140311AA
FREE SAME DAY SHIPPING
Save 36%
List: $124.95 Save: $45.00
Only 2 left in stock
Part 1ADSH00052
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Dorman
Brand #: 935-301

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Highest Quality Materials

Made from highest quality materials that meet or exceed OEM standards

Direct Fit Replacement

Direct fit replacement part guaranteed to fit and function properly for your specific application

Quality Tested

Quality tested and built to a strict level of product standards

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Exhaust (0:57)
    • Disconnect the two oxygen sensor wiring harnesses
    • Remove the two 13mm nuts from the heat shield
    • Pull down the heat shield
    • Remove the two 16mm nuts from the front of the exhaust on each side
    • Remove the 13mm bolt from the hanger bracket at the rear of the exhaust on each side
    • Apply rust penetrant to the exhaust hanger bushings
    • Pull the bushings off the studs with pliers
    • Have an assistant hold up the exhaust
    • Remove the four 13mm nuts from the exhaust cross member
    • Pull the exhaust down and off
    • Pry off the exhaust if necessary
  2. step : Removing the Driveshaft (4:39)
    • Remove the four 11mm nuts from the heat shield
    • Mark the driveshaft and differential positions
    • Put the transmission in neutral
    • Remove the three T60 Torx bolts and 18mm nuts holding the driveshaft coupling to the differential flange
    • Mark the driveshaft and transmission output positions
    • Remove the three T60 Torx bolts and 18mm nuts holding the driveshaft coupling to the transmission output
    • Secure the transmission end of the driveshaft with zip ties
    • Remove the two 13mm bolts from the center bearing
    • Separate the driveshaft from the differential with a prybar
    • Pull the driveshaft down and off
  3. step : Removing the Driveshaft Coupling (8:54)
    • Loosen the 18mm nuts and bolts from the coupling with a socket, ratchet and wrench
    • Pry the coupling off the driveshaft with a pry bar
  4. step : Installing the Driveshaft Coupling (10:20)
    • Remove the spacers from the coupling with a bearing separator if necessary
    • Line up the coupling with the driveshaft
    • Start the bolts into the driveshaft coupling from the shaft side
    • Start the nuts onto the driveshaft bolts
    • Tighten the nuts and bolts with a socket, ratchet, and wrench
    • Hold each nut with an 18mm wrench braced against a solid surface
    • Tighten each bolt to 43 foot-pounds of torque
  5. step : Installing the Driveshaft (12:53)
    • Lift the driveshaft into place
    • Line up the rear of the driveshaft, using your marks from Step 2
    • Start the T60 bolts and 18mm nuts into the rear driveshaft coupling
    • Line up the front of the driveshaft, using your marks from Step 2
    • Start the T60 bolts and 18mm nuts into the front driveshaft coupling
    • Tighten the T60 bolts and 18mm nuts
    • Tighten the T60 bolts to 43 foot-pounds of torque
    • Install the two 13mm bolts into the center bearing bracket
    • Lift the heat shield into place
    • Start the nuts and washers onto the heat shield studs
    • Tighten the 11mm nuts onto the heat shield
  6. step : Installing the Exhaust (15:59)
    • Step 6: Installing the Exhaust [15:59]
    • Line up the exhaust
    • Hold the front of the exhaust with a jack
    • Hold the rear of the exhaust with bungee cords
    • Put the cross member into place
    • Fasten the 13mm nuts onto the cross member
    • Fasten the two 16mm nuts onto each side of the front of the exhaust
    • Put the heat shield into place
    • Install the two 13mm nuts for the heat shield
    • Connect the two oxygen sensor wiring harness
    • Apply penetrating oil to the exhaust hanger bushings
    • Slide the hanger bushings onto their studs
    • Remove the bungee cords
    • Insert the 13mm bolts into the exhaust hanger brackets
    • Start the engine
    • Check for exhaust leaks

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Assistant
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bungee Cord
  • Wire Ties
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Swivel
  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Bearing Separator

  • Star Drivers & Sockets

  • T60 Torx Socket

  • Wrenches - Metric

  • Complete Metric Wrench Set

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Do the bolts come with it?
Erik S May 15, 2019
The bolts are not included.
Andra M May 15, 2019

Fits the following Makes:

Year Make Model Description
2005Chrysler 300 Chrysler 300 V6 3.5L Rear Forward Driveshaft Coupler
2006-2010Chrysler 300 Chrysler 300 V6 3.5L Rear Wheel Drive Automatic Transmission Rear Forward or Rearward Driveshaft Coupler
2006-2010Chrysler 300 Chrysler 300 V8 5.7L Rear Forward Driveshaft Coupler
2009-2010Dodge Challenger Dodge Challenger V6 3.5L Rear Forward Driveshaft Coupler
2011Dodge Challenger Dodge Challenger with Drive Shaft OE # 4593857AC Rear Rearward Driveshaft Coupler
2006-2010Dodge Charger Dodge Charger V6 3.5L Rear Wheel Drive Automatic Transmission Rear Forward or Rearward Driveshaft Coupler
2006-2010Dodge Charger Dodge Charger V8 5.7L Rear Forward Driveshaft Coupler
2005Dodge Magnum Dodge Magnum V6 3.5L Rear Forward Driveshaft Coupler
2006-2008Dodge Magnum Dodge Magnum V6 3.5L Rear Forward or Rearward Driveshaft Coupler
2006-2008Dodge Magnum Dodge Magnum V8 5.7L Rear Forward or Rearward Driveshaft Coupler

Part Interchange

Brand Label Part Number
DIY Solutions ADS00253

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
Dorman
Brand #: 935-301
Product Reviews
There are no reviews for this item.
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Dodge Chrysler Rear Driveshaft Coupler Dorman 935-301-1ADSH00052 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.