Dodge Chrysler Radiator Cooling Fan Assembly DIY Solutions

Vehicle Fit
Warranty & Shipping
How-To & Tools

Part Details

  • Cooling Fan Type:   Dual Fan


  • Radiator Cooling Fan Assembly
  • 100% Performance factory tested
  • Direct replacement
  • Built to strict quality control standards

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Your DIY Solution—Complete Repair in One Purchase

Do you need an assortment of parts to complete a repair? Stop searching for parts individually and complete your repair in a single purchase with a customized kit or set from DIY Solutions.

High-Quality Parts From Trusted Brands

Parts in DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Guaranteed Fit

DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Draining the Radiator (0:53)
    • Raise and support the vehicle on jack stands
    • Have a drain bucket ready
    • Open the petcock at the bottom passenger side of the radiator
    • Let the coolant drain
    • Close the petcock
  2. step : Removing the Radiator Fan Assembly (1:24)
    • Remove the clips on the upper radiator hose with needle nose pliers
    • Slide the hose off of both sides
    • Remove the hose
    • Disconnect the fan wiring harness
    • Remove the harness from the fan
    • Remove the 10mm bolts above the radiator hose fitting
    • Remove the 10mm bolt on the opposite end
    • List the fans up and out
  3. step : Installing the Radiator Fan Assembly (3:35)
    • Remove the wiring harness from the old fan
    • Hook the wire into the new assembly and connect the harness
    • Insert the assembly into place
    • Tighten the 10mm bolts to the radiator fan
    • Connect the fan wiring harness
    • Install the upper radiator hose
  4. step : Filling and Bleeding the Radiator (5:16)
    • Push down and rotate the cap counterclockwise
    • Insert a funnel
    • Fill the vehicle with the 50/50 mix of appropriate coolant and water
    • Start the vehicle
    • Set the fan to the lowest setting
    • Set the heat to the highest setting
    • Keep the coolant level up and monitor the temp on the gauge and out of the vents
    • Wait for a steady flow of heat, bubbles to stop, and steady coolant level
    • Remove the funnel
    • Reinstall the cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Drain Pan
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Gloves
  • Anti-Freeze

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Channel-Lock Pliers
  • Needle nose pliers

  • Screwdrivers & Related

  • Flat Blade Screwdriver

Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does this come with the resistor and harness? If not, where can I get them?
Meredith M May 22, 2018
This does not come with either of those parts, it comes just as pictured.
Tim K May 22, 2018
Does this fan work for a 2.7 engine?
Deshay M June 30, 2018
I don’t know. I used it for a 3.7 engine
S S June 30, 2018
Hello, the engine size is not pertinent to the fitment of this part. I am including a list of vehicle fit below for your reference: 2005-2010 Chrysler 300 Dual 2008-2010 Dodge Challenger 2006-2010 Dodge Charger 2005-2008 Dodge Magnum Thank you!
Zach B June 30, 2018
The one I purchased was for a 2006 Chrysler 300, with a 3.5 liter engine. Yes this fan fit a 2.7 liter engine
Bobby B July 1, 2018
It installed fine on a 2008 Dodge Charger with a 2.7 as for other years, might need to call auto parts or dealer for verification
Michael M July 1, 2018
I works for the 3.5l engine. I dont know anything about the 2.7
K M September 3, 2018
M I September 8, 2019
Will this fit in my 07 300 c 5.7l hemi?
Samuel S June 29, 2019
Yes, according to the information you provided, this part will fit your vehicle.
Corey M June 29, 2019

Fits the following Makes:

Year Make Model Description
2005-2010Chrysler 300 Chrysler 300 Radiator Cooling Fan Assembly
2008-2010Dodge Challenger Dodge Challenger Radiator Cooling Fan Assembly
2006-2010Dodge Charger Dodge Charger Radiator Cooling Fan Assembly
2005-2008Dodge Magnum Dodge Magnum Radiator Cooling Fan Assembly

Part Interchange

Brand Label Part Number
Chrysler 5137717AB-PFM
Chrysler 5137717AB
DIY Solutions HVA02140
Dodge 5137717AB-PFM
Dodge 5137717AB
Partslink CH3115132

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Product Reviews
4.89/ 5.0
9 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Cooling fan
The fan works great. Got it in a timely manner. Im glad that I saw this site because the pricing was on time for me. Everyone else didnt have it.
July 5, 2017
Perfect paet.
Fit perfectly. Showed up as we were told it would Awesome
July 16, 2018
Part was exact match, delivery was quick..the videos are very helpful...
October 20, 2018
Great website to buy parts
I love; it’s so easy to find the right parts needed and they are they have the cheapest price online
May 12, 2019
Great Product
The radiator are great, they’ve been working good so far but I was disappointed that it didn’t have the hangers on one side to hang the cable I had to use zip ties to do so but overall it’s good!
July 1, 2019
2007 Chrysler 300c 5.7 hemi
Installation was easy, does not come with wires so i used the wires from the broken fan. Fits perfectly with no issue.
July 20, 2019
Chrysler 300c radiator fans
The fans I purchased were a better than oem replacement. They fit perfectly and were more quiet than stock fans when they come on. Definetly recommend getting these.
July 29, 2019
300c cooling fans
There is no dislikes and yes I would recommend it to someone
September 8, 2019
Perfect fit. Part was easy to install.
November 7, 2019
Part 1ARFA00240
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: HVA02140