Dodge Chrysler Fuel Injector 8 Piece Set

Frequently bought together

Vehicle Fit
Warranty & Shipping
How-To & Tools
Product Reviews

Part Details

  • Quantity:   8 Piece Set


  • (8) - Brand New Fuel Injectors
  • Replaces dealer part number: 53032713AB
  • Built to strict quality control standards
  • Direct replacements
  • 100% factory tested
  • Correct for models with the following engines per application:
    • V8 5.7L

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Disconnecting the Connector (0:47)
    • Find the connector behind the inner wheel well liner on the driver's side fender
    • Pry back the red safety
    • Lift up the gray latch
    • Open the fuel door
    • Remove the fuel cap
    • Start the truck so it dies
    • Keep cranking to run the system out of fuel
  2. step : Disconnecting the Battery (1:52)
    • Disconnect the negative battery terminal with a 10mm wrench
  3. step : Removing the Air Intake (2:00)
    • Release the clips and open the air filter housing box
    • List the air filter housing box cover up and off
    • Release the PCV hose
    • Loosen the rear clamp on the inlet pipe
    • Remove the box cover and pipe
    • Lift the bottom of the air filter housing box up and out
    • Remove the 10mm bolt behind the alternator
    • Remove the 10mm bolt behind the oil cap
    • Lift the air box up
    • Disconnect the intake sensor
    • Remove the air box
  4. step : Depressurizing the Fuel System (3:03)
    • On the passenger side fuel rail, remove the cap on the Schrader/pressure release valve
    • Place a paper towel below the valve
    • Press down the center of the valve with a pick to release the fuel pressure
  5. step : Removing the Fuel Injectors (3:46)
    • Remove the two 8mm bolts from the fuel rail
    • Clean any dirt or debris from the surrounding area to keep debris from falling in the injector holes
    • Pry up the red safety tab on the fuel injector
    • Push down and remove the connector from the injector
    • Pry out the retaining clip on the backside of the injector with a flat blade screwdriver
    • Evenly lift up the fuel rail, popping out one side at a time
    • Pull the fuel rail up and work the injector out of the fuel rail
  6. step : Installing the Fuel Injectors (5:54)
    • Lubricate the gasket on the fuel injector with a bit of gas from the rail
    • Insert the fuel injector into the fuel rail
    • Press the retaining clip on the back side
    • Press the rail into the manifold
    • Reconnect the injector wiring harness
    • Reinstall the two 8mm bolts
    • Screw the Schrader valve cap on
  7. step : Reinstalling the Air Intake (7:09)
    • Insert the air box with the silicone gasket over the throttle body
    • Tighten the two 10mm bolts to the box
    • Connect the air temp sensor
    • Insert the air filter housing into its mounting spots
    • Insert the intake tube to the air box
    • Tighten the hose clamp
    • Connect the PCV hose
    • Lock the air filter housing box
  8. step : Disconnecting the Connector (8:22)
    • Bring the latch on the connector back down
    • Reinstall the red safety tab
    • Reinstall the fuel cap
  9. step : Reconnecting the Negative Battery Terminal (8:44)
    • Tighten the 10mm bolt to the negative battery terminal
  10. step : Priming the Fuel System (9:09)
    • Turn the key to the on position
    • Turn the key off
    • Repeat the process three times
    • You might hear a high idle
    • Run the engine for a few seconds for the idle to drop to normal levels

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Cloth Rags

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 10mm Socket

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
purchased these injectors for my 2005 dodge ram 1500 5.7l since it sat for nearly 1-1/2 years. The old injectors were stuck open and some clogged. These injectors were will packaged in new boxes individually wrapped in plastic. Simple install and for those unsure of the process there is even a video on the item page. Truck runs ilike new again. I would definitely recommend 1aauto to friends who do their own work on their cars. I even just purchased a new mad sensor and housing for my mustang gt from 1aauto hopefully I will continue to have good luck with their products.
February 27, 2017
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
2007-2008Chrysler Aspen Chrysler Aspen V8 5.7L Fuel Injector 8 Piece Set
2004-2008Dodge Durango Dodge Durango V8 5.7L Fuel Injector 8 Piece Set
2004-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck V8 5.7L Fuel Injector 8 Piece Set
2004-2008Dodge Ram 2500 Truck Dodge Ram 2500 Truck V8 5.7L Fuel Injector 8 Piece Set
2004-2008Dodge Ram 3500 Truck Dodge Ram 3500 Truck V8 5.7L Fuel Injector 8 Piece Set
Only 3 left in stock
Part 1AEEK00228
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.