Replaces
Replaces 2005-07 Dodge Chrysler 4 Piece Lighting Kit DIY Solutions LHT04181
$152.95
Replaces Dodge Chrysler Driver & Passenger Side 2 Piece Headlight Set DIY Solutions LHT03136
$92.95
Replaces 2004-07 Dodge Chrysler Driver & Passenger Side 2 Piece Tail Light Set DIY Solutions LHT07365
$89.95
Replaces 2004-07 Dodge Chrysler Driver Side Tail Light Eagle Eyes CS206-B000L
$54.95
Replaces 2004-07 Dodge Chrysler Passenger Side Tail Light Eagle Eyes CS206-B000R
$54.95
Replaces Dodge Chrysler Driver Side Headlight Assembly Eagle Eyes CS090-B001L
$53.95
Replaces Dodge Chrysler Passenger Side Headlight Assembly Eagle Eyes CS090-B001R
$53.95
Part Details
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
This video is brought to you by 1AAuto.com your source for quality replacement parts and the best service on the internet.
Here we are replacing a headlight on a 2003 Chrysler Voyager. This is the same for a 2001 to 2007 Caravan, Grand Caravan, Chrysler Town and Country and as in this case a Chrysler Voyager. This process is actually very simple. The headlight is only held in by three screws. In this case, we're saving this person over $2000 as they got a quote for just over $2000 to replace the bumper cover, the fender and the headlight, obviously including painting. In a case like this where the owner of the car doesn't want to spend that much money on this old vehicle, this works out very well. They can get the headlight on our website www.1AAuto.com, buy it new. It takes about five minutes to replace it and they're up and running. They can pass inspection no problem.
Now we'll get to it. You're going to see the camera fumble around a little bit as they put it on to a tripod. The tools are very basic. It's a Phillips screwdriver and a regular screwdriver. The first thing you do is there are three screws on top, here, here and here. Remove those screws. You can see as he starts removing the screws the headlights start shifting a bit. Now the headlight is free to pull out. First he's going to remove the signal light with just twist and it pulls out. Now he's going to remove the headlight by pulling off the retainer ring and then pulling out the headlight. Then there's a small clip that holds the wiring harness to the headlight. This takes a little bit of finagling I guess, use the screwdriver to press on the teeth of the clip and you can work it out of the hole in the headlight.
Once it's free, you can just drop the old headlight no problem. Now, handle your new headlight with a little more care. Locate it in there. Get the harness and that clip. You're going to want to put that clip right back into that same hole and the new headlight that presses right in. Now this new headlight came with a bulb in there so we had to remove the bulb from the harness so he's just plugging the harness right into the headlight. Then the signal light goes in and twists just like it came out. Then you can slide the headlight in. As you can see on this car the damage wasn't severe enough so the headlight can go in there without any problem. If you hit a brick wall any faster than four or five miles an hour you might have more damage.
Now you take the screws and you put them into place first then take your screwdriver and you press down and in and the screws find their way into the clips. All three screws at once do them lightly at first so you get them all in and then go back and tighten them up afterwards. You can tighten that one. Then check this one and make sure it's tight and then the last one, make sure it's tight. That's it.
Now we'll do a little quick test make sure the headlight and side light works. That's it, so you saved yourself anywhere from $1000 to $2000 if you had a small accident in the front and you broke your headlight which is great on this great. It's a 2003 so we didn't want to spend a whole lot of money. Now it can go and it can pass inspection without any problem. You can find the part at www.1AAuto.com.
This video is brought t you by 1A Auto your source for quality replacement parts and the best service on the internet. We hope this helps you with your project and we thank you for watching.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi. I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the taillight on this 2005 Chrysler Town & Country. It's a pretty easy procedure, and the only tool you will need is either some type of clip removal tool, or I just use a flat blade screwdriver, as you will see.
To service your rear taillight, you will want to open up your tailgate and then there's basically two plugs right here, and what you want to do is take a flat blade screwdriver, work it in behind and you'll have to just kind of work at it a little bit, and these pins will kind of start coming out. And what you're prying on is actually the center of the pin.
I'm sure Chrysler has some special tool. Once you get it started out, just grab a hold of it and pull it. The pin comes out. We can get the other one a little quicker. Okay. The pin comes out and now your light pulls right out. If you're just looking to replace bulbs, squeeze right there. The socket comes out and these bulbs just pull right straight out and go back in; same thing with this lower one.
If you want to change your entire assembly, because you've had one broken, that's where the new ones from 1A Auto come in great. There's a little kind of safety tab here, push it out. New light from 1A Auto makes a great replacement. It is designed slightly differently than the old one. The problem with these old ones is sometimes these connector plates go bad because they rely on metal contacts and these sockets are not always reliable, so if you're having a problem with your rear taillights lighting up or if, obviously, you have a broken one the 1A Auto one will help that situation. Take it, okay, it still plugs in exactly the same, lock it in. There is a tab on the side here, feeds right into here. Everything lines up the same as the original. Put your pins in and make sure you push them all the way in and then push the middle in and you're all set.
We hope this helps you out. Brought to you by 1AAuto.com, your source for replacement parts and the best service on the Internet. Please feel free to call us toll free at 888 844-3393. We're the company that's here for you on the Internet and in person.
