Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

Our axles are NEW. They are made to the same OEM specifications out of high strength alloy.

Specifications:

  • Comes as a PAIR
    • Fits LH (Driver Side) and RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 49500-2C710, 49500-2D510, 49500-2D511, 49500-2D512, 49500-2D513, 49501-2C710, 49501-2D510, 49501-2D511, 49501-2D512, 49501-2D513, 495012C710, 495012D510, 495012D511, 495012D512, 495012D513, 495002C710, 495002D510, 495002D511, 495002D512, 495002D513
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:53)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Remove the hub cap
    • Pull off the wheel
  2. step : Removing the Sway Bar Link (1:12)
    • Remove the cotter pin from the axle with needle nose pliers
    • Remove the 32mm nut from the axle with a breaker bar and pipe for leverage
    • Turn the wheel by hand
    • Hold the upper sway bar link bolt with a 14mm wrench
    • Remove the upper 14mm nut from the sway bar link
    • Hold the lower sway bar link bolt with a 14mm wrench
    • Remove the lower 14mm nut from the sway bar link
    • Pull off the sway bar link
  3. step : Separating the Control Arm (3:58)
    • Loosen the 19mm nut from the lower ball joint
    • Strike the wheel spindle with a hammer to loosen the ball joint
    • Remove the 19mm nut
    • Separate the lower ball joint from the wheel spindle
  4. step : Removing the Axle (5:55)
    • Strike the axle end with a hammer to loosen it up
    • Separate the axle from the wheel
    • Have a drain pan ready
    • Pry the axle away from the transmission with a drain pan
    • Allow the transmission fluid to drain
    • Pull the axle shaft out
  5. step : Installing the New Axle Shaft (6:51)
    • Feed the axle into place through the wheel well
    • Line up the axle splines with the transmission
    • Push the axle into the transmission
    • Apply penetrating oil to the axle splines
    • Push the axle into the wheel
  6. step : Reattaching the Control Arm (7:57)
    • Push the ball joint into the steering knuckle
    • Start the 19mm nut onto the ball joint
    • Put the center nut onto the axle
    • Tighten the center nut to 175 foot-pounds of torque
    • Hammer the cotter pin into the center nut
    • Bend the cotter pin into place with needle nose pliers
    • Tighten the 19mm nut
  7. step : Reinstalling the Sway Bar Link (9:09)
    • Put the sway bar link into place
    • Fasten the 14mm nuts onto the sway bar link, holding the bolts with a wrench
  8. step : Reattaching the Wheel (10:05)
    • Slide the wheel into place
    • Put the hub cap on
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Drain Pan
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • 1/2 Inch Breaker Bar
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 22mm Socket
  • 32mm Socket

  • Wrenches - Metric

  • 19mm Wrench
  • 14mm Wrench

  • Wrenches - SAE

  • 9/16 Inch Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2006 Hyundai Elantra Front CV Axle Shaft Pair for Models with Automatic Transmission
  • 2003-2008 Hyundai Tiburon Front CV Axle Shaft Pair L4 2.0L with Automatic Transmission
  • 2004 Kia Spectra Front CV Axle Shaft Pair L4 2.0L with Automatic Transmission
  • 2005-2006 Kia Spectra Front CV Axle Shaft Pair for Models with Automatic Transmission
  • 2005-2006 Kia Spectra 5 Front CV Axle Shaft Pair for Models with Automatic Transmission

This part replaces:

  • Hollander 447-60785CL
  • Hollander 447-60782CR
  • OE # 495012D512
  • OE # 495002D512
  • A1 Cardone 66-3469
  • A1 Cardone 66-3467
Part #: 1AACS00081



How-to Video:

(11:05 min)