Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This replacement front lower control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits RH (Passenger Side) FRONT LOWER
  • Arm includes both bushings and ball joint
  • Replaces dealer part number: 22730776
  • Direct replacement
  • Built to strict quality control standards

Worn control arm bushings can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace that heavily rusted, rotted, or damaged front lower control arm with the loose bushings with our high quality all in one replacement.

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

    It is recommended to seek a professional alignment after completing this repair.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Front Control Arm (1:20)
    • Loosen the ball joint bolt with a 15mm wrench and a 16mm socket and ratchet
    • Remove the 18mm bolt in the front of the control arm with a socket, ratchet, and pipe for leverage
    • Remove the two 18mm bolts in the large control arm bushing
    • Remove the bolt on the end of the bushing
    • Pry the front of the control arm out with a pry bar
    • Pry out the back bushing with a pry bar
    • Pull the control arm down and out
  3. step : Installing the Front Control Arm (3:29)
    • Insert the ball joint in place
    • Tighten the 16mm bolt in the ball joint by hand
    • Feed the rear part of the control arm and the front part into the frame
    • Hammer the ball joint into place to line it up
    • Tighten the 18mm bolts by hand
    • Tighten the bolt on the end of the bushing by hand
    • Tighten the 18mm bolts on the control arm bushing with a socket and wrench
    • Torque the bolts between 75 and 85 foot-pounds
    • Torque the ball joint bolt to 50 foot-pounds
    • Place a jack underneath the lower ball joint to lift the suspension up until there's just weight off the jack stand
    • Tighten the rear bushing bolt to 55 foot-pounds of torque and the front 18mm bolt to 75 foot-pounds
  4. step : Reattaching the Wheel (5:41)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Ratchet
  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket

  • Wrenches - Metric

  • 15mm Wrench
  • 18mm Wrench

4.50/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
0
0
0
Good quality it appeared.
With a little work I got it to slip in. Probably should have installed the ball joint 1st as it was the most difficult to line up. Been installed for 2 months and feels like its holding up.
January 23, 2017
llllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll
March 2, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
What material is this made of?
Jay B July 11, 2018
Idk metal. Works great in my car
E O July 11, 2018
Aluminum with rubber & metal inserts.
C A July 11, 2018
Aluminum, rubber bushings, steel ball joint.
B U July 11, 2018
aluminum
Dennis S July 11, 2018
What material is this part?
Jay B July 11, 2018
We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle.
Elesban A July 11, 2018
Year Make Model Description
2004-2005Chevy Malibu Chevy Malibu New Body Style Front Lower Control Arm with Ball Joint Passenger Side
2006-2012Chevy Malibu Chevy Malibu Front Lower Control Arm with Ball Joint Passenger Side
2004-2007Chevy Malibu Maxx Chevy Malibu Maxx Front Lower Control Arm with Ball Joint Passenger Side
2005-2010Pontiac G6 Pontiac G6 Front Lower Control Arm with Ball Joint Passenger Side
2007-2009Saturn Aura Saturn Aura Front Lower Control Arm with Ball Joint Passenger Side
Part #: 1ASLF00182


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(06:36 min)