Chevrolet Toyota Geo Front Wheel Bearing Pair Timken TKSHS00600

Vehicle Fit
Warranty & Shipping
How-To & Tools
Product Reviews

Part Details

  • Quantity:   Pair


These replacement wheel bearings are just what you need to get your vehicle in good working order again.


  • Brand New Timken Wheel Bearings
  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 90080-36040, 90363-3800677, 90369-38010, 90369-38011, 94846348, 94852757, 9008036040, 903633800677, 9036938010, 9036938011
  • Direct replacements
  • Built to strict quality control standards

These wheel bearings make great replacements and have good cost savings over the dealer parts!

These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:22)
    • Raise the vehicle with minimal weight on the wheel
    • Loosen the 21 mm lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Remove the wheel
  2. step : Removing the Knuckle (2:21)
    • Remove the tie rod cotter pin
    • Remove the 19 mm tie rod castle nut
    • Hammer on the side of the knuckle to loosen the tie rod
    • Remove the tie rod from the knuckle
    • Remove the two 17 mm caliper bracket bolts
    • Remove the brake caliper assembly and hang it to the side
    • Remove the brake rotor
    • Remove the axle nut cotter pin
    • Remove the axle nut lock ring
    • Remove the 30 mm axle nut using a long pry bar between the wheel studs to brace the wheel from turning
    • Mark the top strut mount bolt and strut to be able to return the bolt to the same orientation later
    • Remove the 18 mm nut from the 15 mm top lower strut mount bolt
    • Remove the 19 mm nut from the 19 mm bottom lower strut mount bolt
    • Remove the top bolt and leave the bottom bolt to support the knuckle
    • Remove the two 17 mm ball joint mounting nuts
    • Remove the 17 mm ball joint mounting bolt
    • Remove the strut bolt
    • Pull the knuckle downward while supporting the axle so that it does pull out with the knuckle
    • Remove the knuckle
  3. step : Removing the Hub and Bearing (14:06)
    • Pry up to remove the outside inner bearing seal
    • Pry out the inside inner bearing seal
    • Remove the bearing snap ring
    • Press the wheel hub out of the bearing from the inside of the knuckle, making sure to apply pressure only to the hub
    • Press the bearing out from the front of the knuckle making, sure to apply pressure to the outer race of the bearing
  4. step : Installing the Hub and Bearing (26:28)
    • Press the new bearing into the knuckle from the inside of the knuckle, making sure to apply pressure only to the outer race of the bearing
    • Press until you can feel the bearing stop
    • Install the snap ring into the groove in the knuckle
    • Set the knuckle on the base of the press so that only the inner race of the bearing is in contact
    • Align the hub with the center of the bearing and press it in
    • Apply RTV sealer to the inner inside bearing seal and tap it in
    • Replace the outer inside seal
  5. step : Installing the Knuckle (36:38)
    • Apply anti-seize grease to the axle splines
    • Install the Knuckle by seating the ball joint mounting studs into the lower control arm and then inserting the axle into the hub, and then aligning the knuckle into the lower strut mount
    • Install the 19 mm lower strut mount bolt
    • Install the 17 mm ball joint mount nuts
    • Install the 17 mm ball joint mount bolt
    • Torque the 17 mm ball joint mount bolt and the two 16 mm nuts to 106 ft-lb
    • Install the top 15 mm strut mount bolt aligned with the markings
    • Torque the bottom strut mount bolt to 203 ft-lb
    • Torque the top 15 mm strut mount bolt to 203 ft-lb
    • Install the brake caliper assembly
    • Install the 17 mm brake caliper bracket bolts
    • Apply thread locker to the axle
    • Install the 30 mm axle nut
    • Install the tie rod into the knuckle
    • Install the 19 mm tie rod castle nut and torque it to 36 ft-lb
    • Tighten the castle nut further if necessary to align it with the cotter pin hole
    • Install a cotter pin and peen it over
    • Torque the 30 mm axle nut to 159 ft-lb
    • Install the axle nut lock ring, and a cotter pin, and peen the cotter pin over
  6. step : Installing the Wheel (47:42)
    • Install the wheel onto the wheel studs
    • Install the 21 mm lug nuts and tighten them by hand
    • Lower the vehicle with minimal weight on the wheel
    • Torque the 21 mm lug nuts to 76 ft-lb in a crossing pattern

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • RTV

  • Pliers, Cutters & misc Wrenches

  • Pliers
  • Snap Ring Pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 21mm Socket
  • 30mm Socket

  • Specialty Tools

  • Press

  • Wrenches - Metric

  • 15mm Wrench
  • 19mm Wrench

There are no reviews for this item.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
1998-2002Chevrolet Prizm Chevrolet Prizm Front Wheel Bearing Pair
1989-1990Geo Metro Geo Metro Front Wheel Bearing Pair
1991-1997Geo Prizm Geo Prizm Front Wheel Bearing Pair
1988-2002Toyota Corolla Toyota Corolla Front Wheel Bearing Pair

Part Interchange

Brand Label Part Number
DIY Solutions HUB01514
DIY Solutions HUB01114

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Only 1 left in stock
Part TKSHS00600
In Stock

Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Brand #: TKSHS00600