Chevy Malibu Window Regulator - 1AWRG01793

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Regulator Option:   with Motor
  • Operation:   Power


  • LH (Driver Side) FRONT DOOR
  • Replaces dealer part numbers: 15843329, 25802961
  • 100% tested prior to leaving the factory
  • Direct replacements
  • Built to strict quality control standards
  • 2008 Malibu: Fits Classic Body style Models
    • Does NOT fit New Body style Models

Please Note:

This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!

Direct Fit

Direct fit, pre-assembled parts made ready to fit your vehicle and provide easy and trouble-free installation.

Rigorously Tested

Build to strict quality standards

Highest Quality Materials

Made from the highest quality materials for extreme durability and premium performance.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:42)
    • Pry off the trim piece inside the door pull with a flat blade screwdriver
    • Remove the two T25 Torx screws inside the door pull
    • Pry off the door handle bezel with a flat blade screwdriver
    • Disconnect the door lock wiring harness
    • Pry up the window switch panel with a flat blade screwdriver
    • Disconnect the window switch wiring harnesses
    • Pry the two plastic clips out of the rear edge of the door panel
    • Pry out the door panel with a door panel clip tool or putty knife
    • Pry off the speaker cover
    • Lift the door panel up and off
    • Disconnect the trunk lock wiring harness
    • Carefully peel off the water shield
    • Punch out the door handle rivet with a hammer and punch
    • If the rivet doesn't come out, drill it out with a 1/4" drill bit
    • Pull off the door handle
    • Unclip the door handle from the latch rod
  2. step : Removing the Window Regulator (5:55)
    • Lower the window by hand
    • Remove the two 10mm bolts that hold the window to the regulator
    • Raise the window by hand
    • Hold the window in place with painter's tape
    • Remove the two lower 10mm bolts from the regulator
    • Remove the 10mm bolt from the window motor
    • Loosen the two upper bolts from the regulator
    • Disconnect the window motor lead
    • Pull the window regulator out through the door
  3. step : Installing the Window Regulator (10:28)
    • Push the regulator into the door
    • Hang the regulator by its upper bolts
    • Start the lower two 10mm bolts into the window regulator
    • Start the 10mm bolt into the window motor
    • Connect the window motor lead
    • Tighten the five 10mm bolts
    • Remove the painter's tape from the window
    • Lower the window onto the regulator
    • Insert the two 10mm bolts that hold the window to the regulator
    • Connect the window switch wiring harness
    • Test the window switch
    • Disconnect the window switch wiring harness
  4. step : Installing the Window Regulator (12:28)
    • Clip the door latch rod onto the door handle
    • Put the door handle into place
    • Fasten the handle to the door with a rivet and rivet gun
    • Put the water shield into place
    • Connect the trunk lock wiring harness
    • Lift the door panel into place
    • Push in the door panel clips
    • Push the plastic clips into the rear of the door panel
    • Insert the two T25 screws into the door pull
    • Push on the speaker cover
    • Push in the door pull trim piece
    • Connect the door lock wiring harness
    • Push on the door handle bezel
    • Connect the window switch wiring harnesses
    • Push in the window switch panel

Tools needed for replacement:

    Drills, Drill Bits & Related

  • 1/4 Inch Drill Bit
  • Drill

  • General Tools

  • Center Punch
  • Hammer

  • Materials, Fluids, and Supplies

  • Painter's Tape

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Rivet Gun & Rivets

  • Torx Drivers & Sockets

  • T25 Torx Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2005Chevy Malibu Chevy Malibu New Body Style (4th Vin Digit Z) Front Power Window Regulator with Motor Driver Side
2006-2007Chevy Malibu Chevy Malibu Front Power Window Regulator with Motor Driver Side
2008Chevy Malibu Chevy Malibu Classic Front Power Window Regulator with Motor Driver Side
Part #: 1AWRG01793

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(16:38 min)