Replaces

Chevy GMC Buick Saturn Front & Rear Complete Strut Assembly & Shock Absorber Kit 6 Piece Set

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Part Details

  • Includes:   Front Sway Bar Links
  • Quantity:   6 Piece Set

 

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

    It's recommended to seek an alignment after finishing this repair

  1. step : Removing the Wheel (0:47)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Wiper Arm (1:13)
    • Pry off the wiper arm cap with a flat blade screwdriver
    • Remove the 15mm nut from the wiper arm
    • Remove the wiper arm
    • Repeat the process for the other side
  3. step : Removing the Cowl Panel (1:46)
    • Remove the four clips along the cowl panel with a flat blade screwdriver
    • Remove the ground from the cowl panel
    • Pry off the clip near the edge of the windshield
    • Pry off the adhesive pad on either end of the cowl panel
    • Pry off the clip on the driver side of the cowl panel
    • Pull up on the cowl panel to release it from its clips
    • Pull the cowl panel up and off
  4. step : Removing the Front Strut (3:06)
    • Spray the lower and higher strut bolts with rust penetrant
    • Remove the three of the upper 15mm strut bolts and leave the last one loosened
    • Pry out the clip holding the brake line to the strut with a flat blade screwdriver
    • Remove the 18mm nut from the stabilizer link
    • Pull the stabilizer link aside
    • Remove the two 24mm nuts from the bottom of the strut and knuckle
    • Pry the wiring harness off of the strut
    • Thread the 24mm nuts onto the bolts and hammer them to move the bolts
    • Jack up underneath the knuckle
    • Remove the two bolts from the knuckle
    • Pull the strut off the steering knuckle
    • Remove the last 15mm bolt from the strut
    • Remove the strut
  5. step : Disassembling the Strut (5:27)
    • Place the spring compressors on either side of the spring
    • Tighten each back and forth a little while alternating sides
    • Remove the spark plug piece from a 13/16 spark plug socket with a 90-degree pick
    • Remove the nut at the top of the strut with a 7/8 wrench and 13/16 spark plug socket
    • Pull the mount plate from the top of the strut free
    • Remove the spring
    • Pull the boot up and off
  6. step : Assembling the Strut (6:40)
    • Remove the nut from the new strut
    • Replace the boot
    • Insert the spring into its notch on the strut
    • Tighten the bolt onto the new strut
    • Loosen each of the compressors bit by bit while alternating sides
    • Repeat until the spring compressors pull free
  7. step : Inserting the Front Strut (8:35)
    • Insert the strut into place
    • Push down on the knuckle and place the strut behind it
    • Push the strut onto the knuckle
    • Insert the bolts into the bottom of the strut and knuckle
    • Hammer the bolts in and tighten them
    • Torque the bolts to 120 foot-pounds
    • Jack up the strut into place
    • Replace the upper 15mm strut bolts by hand
    • Insert the harness clip in place on the new strut
    • Insert the clip holding the brake line
    • Insert the stabilizer link in place
    • Tighten the 18mm nut to the link
  8. step : Reattaching the Wheel (10:54)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the three 15mm bolts at the top of the strut
    • Tighten the lug nuts to 45 foot-pounds
  9. step : Reinstalling the Cowl Panel (11:39)
    • Insert any remaining clips into the cowl panel
    • Insert the cowl panel into place
    • Insert the adhesive on either side of the panel
    • Push in the clips along the cowl panel
    • Push on the clip near the edge of the windshield
    • Push in the clip on the driver side of the cowl panel
    • Replace and tighten the ground
  10. step : Reinstalling the Wiper Arm (13:17)
    • Push the wiper arm onto the stud
    • Tighten the 15mm nut to the wiper arm
    • Replace the wiper arm cover
    • Repeat the process for the other side

Tools needed for replacement:

    General Tools

  • Pick
  • Floor Jack
  • Jack Stands

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 15mm Socket
  • 22mm Socket
  • 18mm Socket
  • 24mm Socket
  • 21mm Socket
  • 8mm Socket

  • Sockets - SAE

  • 13/16 Inch Spark Plug Socket

  • Specialty Tools

  • Strut Spring Compression Tool

  • Wrenches - Metric

  • 18mm Wrench

Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Are these oe or better?
Mark B March 28, 2019
1A Autos house brand parts are manufactured by various aftermarket companies specifically for us and built to your vehicles exact OEM specifications.
Peter L March 28, 2019
Why are these so inexpensive? Looking at other places you pay almost the same amount just for 1 strut. Are these any good?
Chad W April 21, 2019
1A Autos house brand parts are manufactured by various aftermarket companies specifically for us and built to your vehicles exact OEM specifications. the parts are also back by a Lifetime Warranty against manufacturer defects. As these items are all within a kit we are able to sell them at a lesser cost. Hope this helps you out!
Jessica D April 22, 2019
Does this part fit a 2012 chevy impala ltz with 18 in tires?
Mayra L July 19, 2019
Thank you for the inquiry. This will not fit your Impala, the only Chevy this fits is the Traverse, they are not interchangeable between models.
Ian P July 20, 2019
So are the struts, completely Assembled with the spring already in place?
Chris W December 19, 2019
Yes they were completely assembled with the springs in place, no compression tools or anything needed. Watch the video, the instructions were pretty good. A couple of beers and a whole lot less money and I had my wifes car back in tip top shape!
T J December 19, 2019
Yes, the struts will come assembled as shown in the listing image. Thank you for the inquiry!
Andra M December 19, 2019
Need struts and shocks fo 2004 Saturn vue Do you have them?
Leonard W February 16, 2020
Thank you for the inquiry! We do carry the Front Strut and Spring Assemblies with the Rear Shock Absorbers for your 2004 Saturn Vue. The part # is 1ASSP01087.
Andra M February 16, 2020
What is the brand name of this parts? Also, how does it compare to the others?
Cedric B March 1, 2020
Its TRQ, I think that is 1A Autos own brand. I installed it over a year ago and quality seems as good as any other OEM part
T J March 1, 2020
1A Autos house brand parts are manufactured by various aftermarket companies specifically for us and built to your vehicles exact OEM specifications. Please let us know if you have any other questions.
Emma F March 1, 2020

Fits the following Makes:

Year Make Model Description
2008-2012Buick Enclave Buick Enclave Front & Rear Complete Strut Assembly & Shock Absorber Kit 6 Piece Set
2009-2012Chevy Traverse Chevy Traverse Front & Rear Complete Strut Assembly & Shock Absorber Kit 6 Piece Set
2007-2012GMC Acadia GMC Acadia Front & Rear Complete Strut Assembly & Shock Absorber Kit 6 Piece Set
2007-2010Saturn Outlook Saturn Outlook Front & Rear Complete Strut Assembly & Shock Absorber Kit 6 Piece Set

Part Interchange

Brand Label Part Number
KYB 349125
KYB SR4206
KYB Shocks & Struts SR4206
KYB Shocks & Struts 349125
MOOG K750155
MOOG Chassis Products K750155
Mevotech MS50832
Monroe 182518
Monroe 172518
Monroe 37315
Monroe Shocks & Struts 37315
Monroe Shocks & Struts 172518
Monroe Shocks & Struts 182518

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Part 1ASFK05476
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.