Replaces

Chevrolet Buick Pontiac Rear Driver or Passenger Side Forward Lateral Link

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A

Specifications:

  • Fits LH (Driver Side) or RH (Passengers Side)
  • Bolts to rear knuckle
  • Fixed
  • Track bar is new, not remanufactured or refurbished
  • Includes new end bushings already installed
  • Commonly called by GM:
    • Front knuckle rod
  • Replaces Forward track bars on applications as listed

 

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:51)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap by hand
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Caliper (1:20)
    • Remove the two 13mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
  3. step : Loosening the Struts (1:54)
    • Apply penetrating oil to the track bar bolts
    • Hold the inside track bar bolt with a 21mm wrench
    • Loosen the inside track bar bolt with a 21mm socket and ratchet
    • Hold the outside track bar bolt with a 21mm wrench
    • Loosen the outside track bar nut with a 21mm socket and ratchet
    • Support the suspension carriage with a jack
    • Remove the four 18mm bolts from the carriage
    • Carefully lower the carriage
    • Remove the outside track bar nut
    • Pull down the track bar
    • Pull off the brake rotor
    • Pull the outside track bar bolt up and out
    • Remove the inside track bar bolt
    • Pull the track bar down and out
  4. step : Installing the New Track Bar (6:43)
    • Remove the two 21mm nuts from the strut
    • Hammer the bolts out of the strut
    • Repeat Steps 1 through 3 on the opposite side
  5. step : Installing the New Track Bar (6:43)
    • Raise the new track bar into place
    • Slide the inside track bar bolt into place
    • Slide the outside track bar bolt into place
    • Push the track bar onto the outside bolt
    • Fasten the washer and 21mm nut onto the outside track bar bolt
    • Raise the suspension carriage with the jack
    • Insert the four 18mm bolts into the carriage
  6. step : Reinstalling the Strut (9:43)
    • Insert the two 21mm bolts into the strut
    • Tap the bolts in with a hammer
    • Fasten the 21mm nuts onto the strut bolts
    • Tighten the 21mm nuts to 120 foot-pounds of torque
  7. step : Reinstalling the Brakes (10:22)
    • Slide the brake rotor on
    • Put on the brake caliper
    • Insert the two 13mm bolts into the brake caliper
    • Repeat Steps 6 and 7 on the opposite side
  8. step : Tightening the Track Bar Bolts (10:53)
    • Lower the suspension onto jack stands
    • Tighten the track bar bolts
  9. step : Reattaching the Wheel (11:31)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket
    • Have the suspension professionally aligned

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 21mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 21mm wrench

There are no reviews for this item.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.

Fits the following Makes:

Year Make Model Description
1997-2005Buick Century Buick Century Rear Driver or Passenger Side Forward Lateral Link
2005-2007Buick LaCrosse Buick LaCrosse Rear Driver or Passenger Side Forward Lateral Link
2008-2009Buick LaCrosse Buick LaCrosse with RPO Code FE4 (Special Ride & Handling Suspension) Rear Driver or Passenger Side Forward Lateral Link
1997-2004Buick Regal Buick Regal Rear Driver or Passenger Side Forward Lateral Link
2000-2013Chevrolet Impala Chevrolet Impala Rear Driver or Passenger Side Forward Lateral Link
2014-2016Chevrolet Impala Limited Chevrolet Impala Limited Rear Driver or Passenger Side Forward Lateral Link
2000-2007Chevrolet Monte Carlo Chevrolet Monte Carlo Rear Driver or Passenger Side Forward Lateral Link
1997-2008Pontiac Grand Prix Pontiac Grand Prix Rear Driver or Passenger Side Forward Lateral Link

Part Interchange

Brand Label Part Number
DIY Solutions SUS06621
Dorman - OE Solutions 905-503
Dorman OE Solutions 905-503
MOOG RK660275
MOOG Chassis Products RK660275

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Part 1ASSL00025
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: SUS06621