Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Frequently bought together
Specify your vehicle's year, make and model to guarantee fit.
If your vehicle isn't listed, search Brake Kits
Part Details
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Replacement Brake Kits Features & Benefits
Item Condition:
New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States).
Shipping is not available to Canada. This item cannot be Shipped to AK Alaska, HI Hawaii, US Territories, P.O. Boxes, APO/FPO/DPO addresses or Expedited due to size limitations.
Created on:
Tools used
Okay, friends. The first thing you need to talk about anytime you're working on your vehicle is safety. You want hand and eye protection. With that said, safely raise and support your vehicle so the wheels are off the ground. Once you've done that, we're going to remove all 5 of our 19-millimeter lug nuts. Remove your wheel. To do the brakes, what we're going to need to do is push back our caliper piston, which is located right inside here. A lot of times, what people like to do is to open up the bleeder screw so that way there you're not forcing any fluid back up through the lines. The only problem with that is if it's in the condition that this one is with a lot of corrosion, more than likely what's going to happen is the bleeder screw is going to break off and you're going to have to buy yourself a caliper. What I would prefer to do is, of course, go ahead and leave this in here, and that'll end up just pushing in the caliper piston slowly. The next thing we're going to do is remove our caliper slider bolts. Using a pry bar, we're going to get the caliper off of here.
You might just have to work it back and forth a little bit. Take a peek at your caliper piston right here and also the boot. You want to make sure that you don't see any tears in the boot, and you also want to make sure you don't see any fluid. If you see fluid, it's probably brake fluid, in which case, you have to replace your caliper. To push back this caliper piston, you're going to need something that's going to be able to fit into those two grooves. We're going to need to twist at the same time as we push in. This isn't the type of piston that you can just go ahead and press in. I have a little tool here that has multiple edges. I found the set that fits in there. So, I'm going to line it up with the slots. I'm going to press and twist at the same time. All right. Set this aside. Now, we're going to go ahead and get the pads out of here. These are really frozen in there.
Now that we have the pads out of there, looking from the backside, you can see your two caliper bracket mounting bolts, remove them both. Next, we're going to take one of our lug nuts, start it right onto one of these lug studs. Spray down the rotor area where it connects onto the hub with a little bit of penetrant. Take your hammer and give it a couple of loving bonks. Remove that lug nut. Remove your rotor. Next, we need to clean up the mating surface where our rotor is gonna ride. Make sure you get it in between the area where your studs and your hub are. You want to make sure there's no raised areas. You can try using a brush, or if you find that there's large chunks, go ahead and use a screwdriver or a pry bar and just go ahead and scrape it right out of there. Okay. So, this looks pretty decent, let's move along to the backside though. If you were to look back here, you're going to see that there's all sorts of raised things, there's loose flakes of rust, there's all sorts of debris. You want to make sure you clean this up as well. If you leave something back there that could break free, it might potentially get behind your rotor or even between your rotor and your pads, which, of course, will cause a major issue.
Once you feel as though you have it cleaned down as well as possible, let's hit it with a little bit of parts cleaner. Let that fully dry. Now, we're going to apply a little bit of copper never-seize to our hub. So, we made it over to the bench so we can clean up our caliper bracket. One of the first things we need to do is get everything off of it that doesn't need to be there. Let's get the tins off of here. Set that aside for recycling. Take your caliper sliders, give them a little twist to pull them right off of there. Once you've done that, go ahead and remove the boots. Always inspect your boot. Make sure it's not torn or worn or crispy or hard. This one looks good. So, we would just take a rag, clean out the inside, do the same to both. That looks great. Now, let's clean up our sliders. You'll notice when you clean these up, one of your sliders is going to have a little rubber boot and then the other one won't. You want to make sure that you put the slider that had the boot in the same corresponding hole that you removed it from. Another thing to think about with your sliders is to check the condition. If it looks like they're rotted and pitting, or even they're rusted to the point that they might get stuck inside here, obviously that's going to be an issue. Make sure you clean this up and especially make sure you clean up this area right here, which is where the boot's gonna ride. If there's anything there that's going to cause a discrepancy where moisture can get in, obviously, you're going to have an issue overall.
We have the sliders and the boots cleaned up. We need to clean out the inside ports on our caliper bracket. This is where the sliders are going to be, and they need to be nice and clean. Grab a nice collection bucket with some hand protection and eye protection. We're going to spray a little bit of cleaner inside there, and then we'll use a bore brush to clean it out completely. Now that we have the ports cleaned up, it's important to make sure that you check this area right here and there. That's also where the slider boots are gonna ride. Make sure those are in good condition. Once you know that those are good as well, we're going to move along to the area where the tins are supposed to be. We need to make sure that there's no raised areas here. You can try to scrape it out. You could use a little brush, see if you can get it out. Or, of course, you can use one of those little sanding discs wheels, those work the best. You want to just make sure you have it nice and clean and a smooth surface. Okay. So, these look great. I did all four corners, they look amazing. One last thing that I'd like to mention, some people don't pay attention to this, but if you look along the rest of the bracket, just kind of make sure you don't have any large flakes. Anything like that could, of course, cause braking issues overall. Okay.
So, now, it's time to add a little bit of lubricant to this. We're going to go along all the areas that we just cleaned up. You want to make sure that you use it. It's going to help with vibration dampening and noise reduction. Now it's going to be time to get our caliper tins on here. You're going to notice they're both the same, so you really don't have to worry about anything. Go ahead and slide it in there. And you want to make sure that it's completely clicked in. It needs to be locked in because if it's free in any way, it could potentially slide in some way and cause a brake issue. Now it's gonna be time to get our caliper boots on there. I always like to take a little bit of lube. I'll just go right along the hole like that. And you especially want to make sure you get it along the outside, along that little ridge. That's gonna help keep moisture out of there. We'll just go ahead and force this up on there. Give it a nice little twist to make sure the lube's completely situated. Do the same to the other one. Now that we have those on there, let's go ahead and take some lube and put it right on the pins. Coat that complete pin all the way around, and, of course, make sure you get up near that lip.
Once you have it completely lubricated, go ahead and slide it inside there and then just kind of work it around a whole bunch of times. You also want to make sure that the boot is sitting in the lip. Give it a little wiggle, do the same to the other side. Okay. Both of those are in, we've got our tins on there. It's nice and clean. Let's get back over to the vehicle. So, we made our way back over towards the vehicle but before we go ahead and get the rotor on here, we want to make sure that we clean it down first. Here's a little bit of parts cleaner. Go ahead and clean the outside braking surface, turn it over, and make sure you clean the inside braking surface. Let's get the rotor up on here. I always like to hold it on with one of my lug nuts. That's just going to keep it from moving around and keep anything from potentially getting in between the rotor and the mating surface of the hub. Let's get our bracket up on here. Start in both of your bracket bolts, snug them up, and then we'll torque them to manufacturer's specifications. I'll torque these to 96 foot-pounds.
It's going to be time to install your pads. What's important to pay attention to is your wear indicator. You want to match up the wear indicator pad to the one that's came off of the vehicle originally so it's in the same spot. The pad with the wear indicator needs to go on the inside portion of the rotor. There we are. Now, we're just gonna take a little bit of that caliper grease, and we're going to go right along the piston area where it's gonna connect onto the pad and then along each of these ears. This is only going on the mating surfaces, and it's to help with vibration dampening and noise reduction once again. Put the caliper up and over your pads, line it up with your sliders, of course. We'll put in both of our bolts, snug them up, and we'll torque those to manufacturer's specs as well. Torque these to 26 foot-pounds. Fill up on here. We'll start on the lug nuts, and then we'll torque them down to 100 foot-pounds. Let's torque these to 100 foot-pounds in a criss-cross manner. Torqued. Let's go ahead and check and top off our brake fluid and pump up the brake pedal.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace or do a rear brake job on this 2007 Pontiac G6. It's the same as any 2005 to 2010 G6, as well as the Saturn Aura. We show you the right hand side, which is the same as the left hand side. You'll need new brakes from 1AAuto.com, jack and jack stands, 13mm, 14mm, and 19mm wrenches as well as sockets, a ratchet, large screwdriver, wire brush, a caliper piston reset tool, and brake or white grease. Our car has good brakes on it so we just take them apart and put them back together to show you.
Start by using a 19mm socket, and depending on what wheels you have, this has wheel covers, so unscrew the caps and then the wheel cover comes off. If you don't have the benefit of air tools, you'll want to loosen the lug nuts with the vehicle on the ground. Then raise and secure the vehicle, and then remove the lug nuts, wheel, and tire.
With the wheel off, you can see our pads have good life. Run the back of your fingernail on the disc. There's no groove. These brakes are actually in pretty good shape. We'll take them apart and put them back together to show you. Holding the caliper is two 14mm bolts. We'll speed up here. We use a 14mm wrench on the bolt. Then we actually have to hold the slides with either a 19mm or a 13/16 wrench. Now use a large screwdriver or small pry bar and just pry between the caliper and the disc. That will help loosen the caliper up a little bit. Now you can lift the caliper off.
Now the pads will pull out. For the inside pad, or maybe even the outside pad, you might want to use a screwdriver for a little extra leverage. Put it in between the pad and the rotor, and just pry it right out. Two 13mm bolt holds the bracket. We'll speed up here as we use a 13mm socket with a ratchet to remove those two bolts and remove that caliper bracket. Then we can remove the disc as well.
In order to put the brakes back together we'll need to reset the piston in the caliper. You need a special tool that actually spins the piston. You can see it there. It's available at most of our auto parts stores. Put that in with an extension. Hook your ratchet up to it, and then hold your caliper steady while you spin the piston back in. You're both turning the piston and pushing it back into the caliper.
Now make sure the slides in your caliper bracket are free. If they're not, if they're gummed up at all, pull them out like that, clean it up, re-grease them. Make sure they're nice and free. Then you'll want to wire brush the stainless steel slides where the brake pads sit.
Reinstall the rotor. Now reinstall the bracket and start the bolts in. Then we'll tighten up the bolts, and you'll want to torque them between 25 and 35 foot-pounds. Now apply a little bit of brake or white grease into the slides where you're going to install the brake pads into. The pads have a little notch in them, so you want to make sure you position the piston at the correct clock position so it'll slide down over the pads. We'll just turn the piston a little bit.
Now we're going to take our pads and put them into the slides. Make sure they go in correctly. They should be nice and free and moveable. Make sure, also, again, that you have the piston lined up so that it will go right down onto the pad. We put the pads in place. I will speed up here as we put the caliper back on. If you have any issue at all with that caliper going down at all onto the bracket, just check your caliper piston. Make sure it's lined up correctly. We'll put those bolts back on with our 14mm as well as our 19mm wrench. You want to just tighten these up nice and snug. They should be about between 18 and 19 foot-pounds.
Speed up here as we put our wheel and tire back on. Just start the lug nuts on there by hand first, and then tighten them preliminarily. With the car back down on the ground, we'll tighten the lug nuts to 100 foot-pounds using a star pattern. Last, but not least, put our wheel cover on there. Put the caps on carefully only using hand power to tighten those caps up. Last, but certainly not least, make sure you pump up the brakes. Get a nice firm pedal before road testing the vehicle.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
Tools used
Tools used
Okay, friends. The first thing you need to talk about anytime you're working on your vehicle is safety. You want hand and eye protection. With that said, safely raise and support your vehicle so the wheels are off the ground. Once you've done that, we're going to remove all five of our 19-millimeter lug nuts. Remove your wheel. Now that the wheel's off, we have a nice, clear view of our caliper. The first thing I always like to do is pinch off the flex hose so there won't be any fluid coming out of it. You will still have fluid coming out of the caliper though, so make sure you have a nice collection bucket for recycling the fluid. Now, we're going to break free our banjo bolt here, and then we're just going to tighten it back up a tiny bit. There we are. The reason why we did that is because it's going to be much easier to do it while the caliper is still mounted, but we want to make sure it's closed so no fluid comes out and potentially gets in our eyes or face.
The next thing we need to do is get our emergency brake cable out of its little bracket area here. To do that, you're going to want to grab onto this little nub right here and just move it around. Make sure it's broken free. Next, I'm going to go ahead and grab on between this lever here and up here. Try to squeeze these together and get my line out of the area it's in. There we are. The cable's free. The next thing we need to do is grab onto our cable and spin it until you can see the little push tab come around. There's going to be one on this side, and then there'll be one on the forward side as well. Take a pick or a screwdriver or whatever you might happen to have, press on that tab, wiggle the cable around a little bit until it comes a little free. Do the same on the other side, and then draw it up and out of your caliper. There we are.
We're going to remove our caliper mounting bolts. There's one here and there's one located up top. There's one bolt. I'm gonna leave this one in a little bit and we're going to fully remove our banjo bolt. Just be careful because brake fluid will come out. Let's go ahead and remove that last bolt. Make sure that you don't have any gaskets left over on your flex hose.
Before you go ahead and install your brand new caliper. It's important to make sure that you lubricate everything and double-check everything. Go ahead and take off these caliper slider bolts right here, and then separate the two pieces. At this point, what we would want to do is take off our tins. And then I also like to take off the sliders. I'll just grab onto this and I'll pull it right out. The reason for that is because I want to make sure that there's a sufficient amount of lubricant inside here. If there isn't enough, there's a possibility that water could get in and, of course, cause damage. Open this up, put on a whole bunch of lubricant, and slide it right on back in there. Do the same to both. Now that we finished up with the sliders, we're going to go right along this area here, where the tins are gonna go. Do this on both sides of the caliper bracket. Now, let's go ahead and put our tins on there. Now, for the muscle part of the caliper, we're going to go ahead and lubricate on the piston right here, where it's going to be pressing directly against the pad. And then, of course, both of these ears.
Time to make our way back over to the vehicle and we're gonna stick this bracket. We'll take the two mounting bolts and I always like to use a little bit of red threadlocker. Go ahead and line it up with the knuckle back here, start in both of your bolts. We'll snug them up and then torque them to manufacturer specifications. Torque these to 96 foot-pounds.
It's gonna be time to install our brake pads. It's important to remember the one with the brake squealer is going to go on the inside portion of the rotor. Take your brake caliper, slide it right over those pads and sliders, and, of course, insert your bolts. We'll snug them up and we'll torque those to specs as well. Now, we're gonna torque this to 26 foot-pounds. Go ahead and hold onto your slider so it can't spin. There it is. Now it's gonna be time to get our e-brake cable back onto the caliper. Just gonna put it right along here, start it in there, just like that. I'll come along the backside here, lift up on this, and then slide it in. And now, I'm just gonna make sure that I lock it in. Give it a nice tug, make sure it's secure. Let's get this little cover out of here. Set it aside because we're going to use it in our old caliper. Now, we're going to need our banjo bolt, double-check it to make sure there's no gasket. Your gasket should look a little bit like this. Once, you're sure that it's clean and does not have a original gasket, put on a brand new gasket. Put it through your line, put on your other gasket. Now, when you put your hose on, you want to put it so it's aiming off towards the inner portion of the vehicle. You definitely don't want to put it so it's facing up because then it will be hitting up against the wheel. Let's go ahead and snug this up and then we'll torque it to 37 foot-pounds. Torqued.
Let's get this off of here. Now, it's gonna be time to bleed the brakes. Next, you want to check your brake fluid level. Make sure you have plenty of brake fluid. If you don't and you need to top it off, you need to use DOT 3 brake fluid. Okay. So, our next step is to bleed the brakes. We want to make sure there's no air in the system. You can either do that by yourself with a special tool or, of course, you can do it with a second person. I have a second person, so that's the way I'm going to do it. I have them inside the vehicle, they're going to pump up the brake three to five times and then hold it. Once they're holding, we're going to open this up and we're going to wait for air/brake fluid to come out. We're going to repeat the process several times until we see no more air coming out of this bleeder screw. Go ahead and pump up the brakes, please. Okay. I heard a lot of air come out of that one, but no fluid. Close it up. Here we go again. Go ahead and pump. So, there's the fluid and air that I was talking about. You saw those little air bubbles. We want to make sure that there's no air inside of your brake system. We need to continue.
So, on that last time around, I didn't see any air come out of the system, but it's always good habit to just go ahead and do it at least one more time just to be sure. Go ahead and pump. All right. So, see, there you go. A little bit more air. Here we go again. So, as you saw, I had two times of bleeding the caliper with no air coming out of it. That should be good enough. If you want to continue, that's completely up to you, we'll call it your prerogative. The next thing we need to do is pump up the brake and hold it one more time. Go ahead. Now, I'm going to try to spin this wheel. We want to make sure that the wheel does not turn at all. That means that the brake's working as it should. Go ahead and let off the brake, please. Give it a little spin, that spins perfectly. That means that everything's functioning as it should that way as well. We also have the e-brake cable here. So, we want to make sure that that's working as it should. Can you please push on the e-brake? Give the wheel a turn. Nothing's happening. The e-brake works perfectly. Go ahead and remove it. Okay. He released it and it spins. This is great.
Now that we tested the emergency e-brake this way, we want to make sure once we get the wheel back on here and it's on the ground, you test the emergency brake with the force of the vehicle. We want to make sure that it works 100%. Let's clean this down. Forget to put it on your bleeder screw cover. Wheel up on here. We'll start on the lug nuts, and then we'll torque them down to 100 foot-pounds. Let's torque these to 100 foot-pounds and a criss-cross manner. Torqued. Let's go ahead and check and top off our brake fluid.
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Brake Kits